Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402524 ROCKER PANEL F

BODY PANEL  ROCKER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K153145

REMOVE THE HEMMING LOCATION


a.
K152597

Grind down the flange edge (1) with an angle grinder with a roughing wheel.


b.

Heat the adhesive flange (2) with a hot air blower.

NOTICE:

Do not exceed the maximum object temperature of 250°C.



c.

Use pliers or a chisel to peel off the components.

NOTICE:

Do not damage adjacent components.



d.

Remove the sealant in the area (3).


e.

Remove adhesive residue (4) from the adhesive flange.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

a.

Mark and perform the separating cuts to match the specified dimensions.

NOTICE:

Thereby disconnect only the outer panel.



b.

Remove the welding points in areas (1).


c.

Remove the adhesive in area (2).


d.

Remove the weld points and adhesive in area (3).


e.

Remove the hemming location in area (4).


f.

Remove the side panel sub-assy outer from the foamed sealing material in areas (5).

K152960C01
5.917,2.26 6.25,1.917 6.25,1.917 6.417,1.917 false 6.469,1.844 6.781,2 0.313,0.156 10 false *1 1.271,0.635 1.583,0.792 0.313,0.156 10 false *a 5.354,0.5 5.667,0.656 0.313,0.156 10 false *b 4.698,3.635 5.01,3.792 0.313,0.156 10 false *c 1.802,2.219 2.115,2.375 0.313,0.156 10 false *a 4.854,1.51 5.167,1.667 0.313,0.156 10 false *b 3.781,1.802 4.094,1.958 0.313,0.156 10 false *c
*1 SIDE PANEL SUB-ASSY OUTER - -
*a centre of hole *b 130 mm (5.12 in.) from the corner of the outer left side frame
*c 65 mm (2.56 in.) from the upper edge of the hole - -
K108837

Adhesive
K108840

Foamed Sealing Material



g.
K152599

Remove the welding points in areas (1).


h.
K152600

Remove the welding points in areas (1).


i.
K155739C01
1.104,0.208 1.417,0.365 0.313,0.156 10 false *a
*a 70 mm (2.76 in.)


Remove the welding points in areas (2).


j.
K152601

Remove the welding points in areas (1).


k.

Remove the front side panel outer.


l.
K152780

Remove the remaining foamed sealing material (1) from the vehicle side.


m.

Remove the welding points in areas (1).

K152961C01
0.427,2.135 0.74,2.292 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) - -



n.
K152962

Remove the welding points in areas (1) and (2).


o.
K152894

Remove the foamed sealing material (1).


p.
K152963

Remove the welding points in areas (1) and (2).



Prepare new part


a.
K152964C01
0.792,0.417 0.667,0.167 0.667,0.167 0.833,0.167 false 0.865,0.104 1.177,0.26 0.313,0.156 10 false *1 0.26,1.219 0.573,1.375 0.313,0.156 10 false *a
*1 SIDE PANEL SUB-ASSY NO.1
*a 120 mm (4.72 in.)


Remove the welding points in areas (2).


b.

Remove (3) from the new parts of side panel sub-assy No.1.


c.

Prepare the new parts for the joining repair method by welding.


d.

Adjust the new part as an assembly consisting of the side panel sub-assy No.1.


e.
K153221

Remove the welding points in areas (1).


f.

Remove a section of the (2).



INSTALLING THE FOAMED SEALING MATERIAL


HINT:
·

Schematic diagram is for example purposes.

·

Some parts may differ in certain details.



a.
K152602

Sand the contact surface of the foamed sealing material (1) with sandpaper (#50-100).


b.

Clean the contact surface (1) with the cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



c.

On the contact surface (1), apply an approximately 15 mm (0.59 in.) bead (2) of brushable seam seal. If necessary apply a slightly thinner bead of brushable seam seal on each side, to prevent the sealant from running.

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230



d.
K152965

Apply brushable seam seal on the inner bottom B-pillar foamed sealing material (1).


e.

Install foamed sealing material (1) in the B-pillar reinforcement (2).


f.
K152966

Apply brushable seam seal on the bottom rear A-pillar foamed sealing material (1).


g.

Install bottom rear A-pillar foamed sealing material (1) in the bottom A-pillar reinforcement (2).


h.

Install wheel arch carrier support foamed sealing material (3) in the rear wheel arch carrier support (4).


i.

Remove existing cavity protection wax in the repair area with cavity protection wax remover.

Expendable materials:
Cavity Wax Remover 500ml, Spray bottle 08830-WA010




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.

Apply brushable seam seal to the foamed sealing material for the carrier support of the wheel arch(1).


b.

Apply brushable seam seal on the bottom front A-pillar foamed sealing material (2).


c.

Apply brushable seam seal on the inner bottom B-pillar foamed sealing material (3).


d.

Position reinforcement of left side sill, align it and fix it with locking pliers.


e.

Weld the cowl side panel sub-assy in the areas (4).

K152967C01
5.844,2.573 6.333,2.917 6.333,2.917 6.5,2.917 true 6.573,2.833 6.885,2.99 0.313,0.156 10 false *1
*1 COWL SIDE PANEL SUB-ASSY - -
*a Ultra High Strength Steel Welding Point - -
K108840

Foamed Sealing Material - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.
K152968

Weld the cowl side panel sub-assy in the areas (1) and (2).


g.
K152969C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point


Weld the cowl side panel sub-assy in the areas (1) and (2).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




h.
K152798

Apply brushable seam seal on the A-pillar shaped part.


i.
K152894

Apply brushable seam seal on the outer bottom B-pillar foamed sealing material (1).


j.
K152970

Apply brushable seam seal on the bottom front A-pillar foamed sealing material (1).


k.

Install bottom front A-pillar foamed sealing material (1) in the outer side frame (2).


l.
K152604C01
0.844,1.563 1,1.719 0.156,0.156 10 false A
A 5 mm (0.20 in.)


Apply adhesive (1) to the new part in the area (2) of the wheel arch.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



m.

Apply adhesive (1) on the inside of the side panel at a distance (A).


n.

Weld the side panel sub-assy outer in the areas (1), (3) and (4).

NOTICE:

When using welds to attach panels that were previously attached using adhesive, it must be welded by plug welding (MAG welding), no adhesive should be applied. The number of plug welds (MAG welding) must be doubled compared to the original welding points on the adhesive applied areas.


HINT:
·

Apply brushable seam seal to the foamed sealing material in the areas (2).

·

Align the front side panel outer in the areas of the separating cuts (1) and (4) and secure it with vise grip.



K152971C01
6,2.438 6.333,2.021 6.333,2.021 6.5,2.021 false 6.563,1.958 6.875,2.115 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSY OUTER - -
K108840

Foamed Sealing Material - -



o.
K152606

Weld the side panel sub-assy outer in the areas (1).


p.
K152607

Weld the side panel sub-assy outer in the areas (1).


q.
K152608

Weld the side panel sub-assy outer in the areas (1).


r.
K152609

Apply adhesive (2) above the side panel (1) on the outer wheel arch section (3).

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



s.
K152610C01
1.719,1.969 2.031,2.125 0.313,0.156 10 false *a
*a 5 mm (0.20 in.)


Flange the edge of wheel arch (3) of the side panel (2) flush to the outer wheel arch section.

NOTICE:

Do not create sharp edges when flanging as otherwise the flange edge may begin to tear.



t.

Fully fill flange edge (1) with adhesive.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



u.

Seal the area of the edge of wheel arch (3) with seam seal.

Expendable materials:
Seam Seal 310ml 08826-WA220



v.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


w.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.