Home › Vehicle Exterior › BODY PANEL › REAR FLOOR SIDE MEMBER
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402530 REAR FLOOR SIDE MEMBER F

BODY PANEL  REAR FLOOR SIDE MEMBER  ASSEMBLY REPLACEMENT  


K153155

With the body lower back panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108829

Cut Location

a.
K152913

Remove the weld points in areas (1).


b.
K152907C01
0.25,1.917 0.417,1.917 0.417,1.917 0.583,1.667 false 0.104,1.802 0.417,1.958 0.313,0.156 10 false *1 0.115,1.969 0.427,2.125 0.313,0.156 10 false *2
*1 REAR FLOOR PAN EXTENSION (LH)
*2 REAR FLOOR SIDE PANEL EXTENSION (RH)


Remove the weld points in areas (1).


c.

Remove the rear floor pan extension or rear floor side panel extension.

HINT:

To provide a better overview: Side panel omitted for clarity.



d.
K154693

Remove the weld points in areas (1).


e.
K152624C01
0.792,0.708 0.667,0.25 0.667,0.25 0.5,0.25 false 0.333,0.177 0.646,0.333 0.313,0.156 10 false *1
*1 REAR FLOOR PANEL REAR


Remove the weld points in areas (1).


f.

Remove the rear floor panel rear.


g.
K152914C01
0.688,1.24 0.417,1 0.417,1 0.25,1 false 0.083,0.917 0.396,1.073 0.313,0.156 10 false *1
*1 REAR FLOOR SIDE MEMBER REAR


Remove the weld points in areas (1) and (2).


h.

Remove the rear floor side member rear.


i.
K152915

Remove the weld points in areas (1).


j.
K152916C01
2.25,1.833 2.083,1.833 2.083,1.833 2.042,1.417 false 2.354,1.75 2.667,1.906 0.313,0.156 10 false *1
*1 REAR FLOOR SIDE MEMBER REINFORCE SUB-ASSY REAR


Remove the weld points in areas (1) and (2).


k.

Remove the rear floor side member reinforce sub-assy rear.



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld

a.
K152917C01
1.5,2 1.667,2 1.667,2 1.75,1.75 false 2.563,1.313 2.833,0.833 2.833,0.833 3,0.833 false 1.333,1.917 1.646,2.073 0.313,0.156 10 false *1 3.073,0.76 3.385,0.917 0.313,0.156 10 false *2
*1 REAR FLOOR SIDE MEMBER REINFORCE SUB-ASSY REAR
*2 REAR SUSPENSION MEMBER MOUNTING BRACKET SUB-ASSY RR


Adjust and fix rear floor side member rear in the lower section of the rear floor side member reinforce sub-assy rear.


b.

Before temporarily installing the new parts, weld the rear floor side member reinforce sub-assy rear and rear suspension member mounting bracket sub-assy RR with the standard number of welding points.


c.
K152918C01
2.5,1.917 2.333,1.917 2.333,1.917 2.208,1.521 false 2.583,1.844 2.896,2 0.313,0.156 10 false *1
*1 REAR FLOOR SIDE MEMBER REINFORCE SUB-ASSY REAR
*a Ultra High Strength Steel Welding Point


Install and fix rear floor side member reinforce sub-assy rear.


d.

Weld the rear floor side member reinforce sub-assy rear in the areas (1).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




e.
K152919C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point


Weld the rear floor side member reinforce sub-assy rear in the areas (1).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 780 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.
K152920C01
0.573,1.125 0.417,1 0.417,1 0.25,1 false 0.073,0.938 0.385,1.094 0.313,0.156 10 false *1
*1 REAR FLOOR SIDE MEMBER REAR
*a Ultra High Strength Steel Welding Point


Install, align and fix rear floor side member rear (1) and therear bumper arm support reinforce (2).


g.

Weld the rear floor side member rear (1) in the areas (3) and (4).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




h.
K152921C01
0.167,0.25 0.333,0.25 0.333,0.25 0.417,0.771 false 0.021,0.177 0.333,0.333 0.313,0.156 10 false *1
*1 REAR BUMPER ARM SUPPORT REINFORCE
*a Ultra High Strength Steel Welding Point


Weld the rear bumper arm support reinforce in the areas (1) and (2).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa or 780 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




i.
K154694C01
1.833,1.917 2,1.917 2,1.917 2.031,1.656 false 1.667,1.833 1.979,1.99 0.313,0.156 10 false *1
*1 REAR FLOOR PANEL REAR


Install, adjust and secure the rear floor panel rear.


j.
K152626

Weld the rear floor panel rear in the areas (1).


k.
K152909C01
0.25,1.917 0.417,1.917 0.417,1.917 0.521,1.615 false 0.083,1.802 0.396,1.958 0.313,0.156 10 false *1 0.094,1.979 0.406,2.135 0.313,0.156 10 false *2
*1 REAR FLOOR PAN EXTENSION (LH)
*2 REAR FLOOR SIDE PANEL EXTENSION (RH)


Insert and secure rear floor pan extension or rear floor side panel extension from below.


l.

Weld the rear floor pan extension or rear floor side panel extension in the area (1).

HINT:

To provide a better overview: Shown without side panel and without tail panel.



m.
K152922

Weld the rear floor pan extension or rear floor side panel extension in the areas (1).


n.
K152911

Weld coarse thread bolt (1) on the new part.

HINT:

Take the quantity and position from the component to be replaced.



o.
K152923

Weld coarse thread bolt (1) on the new part.

HINT:

Take the quantity and position from the component to be replaced.



p.
K152627

Weld coarse thread bolt (1) on the new part.

HINT:

Take the quantity and position from the component to be replaced.



q.
K152628

Weld coarse thread bolt (1) on the new part.

HINT:

Take the quantity and position from the component to be replaced.



r.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


s.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.