Home › Vehicle Exterior › BODY PANEL › ROCKER REAR PANEL
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402533 ROCKER REAR PANEL F

BODY PANEL  ROCKER REAR PANEL  ASSEMBLY REPLACEMENT  


K153147

With the quarter panel cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108829

Cut Location

a.
K152894

Remove the foamed sealing material (1).


b.
K152895N01
2.292,0.708 2.75,1 2.75,1 2.917,1 false 2.969,0.906 3.125,1.104 0.156,0.198 10 true A

Remove the weld points in areas (1) and (2).


c.
K152896N01
1.896,1.302 2.417,1.833 2.417,1.833 2.583,1.833 false 2.635,1.74 2.792,1.938 0.156,0.198 10 false A

Remove the weld points in areas (1).



PREPARE NEW PART


a.
K152897C01
1.052,1.583 0.833,1.167 0.833,1.167 0.667,1.167 false 0.49,1.083 0.802,1.24 0.313,0.156 10 false *1
*1 COWL SIDE PANEL SUB-ASSY


Remove the weld points in areas (1).


b.

Remove (2) from the new parts of cowl side panel sub-assy.


c.

Remove existing cavity protection wax in the repair area with cavity wax remover.

Expendable materials:
Cavity Wax Remover 500ml, Spray bottle 08830-WA010




INSTALLING THE FOAMED SEALING MATERIAL (NOT EXPANDED)


HINT:
·

Schematic diagram is for example purposes.

·

Some parts may differ in certain details.



a.
K152602

Sand the contact surface of the foamed sealing material (1) with sandpaper (#50-100).


b.

Clean the contact surface (1) with the cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



c.

On the contact surface (1), apply an approximately 15 mm (0.59 in.) bead (2) of brushable seam seal. If necessary apply a slightly thinner bead of brushable seam seal on each side, to prevent the sealant from running.

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230



d.
K152898

Apply brushable seam seal on the inner bottom B-pillar foamed sealing material (1).


e.

Install inner bottom B-pillar foamed sealing material (1) in the B-pillar reinforcement (2).



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.
K152899C01
0,0 0,0 false
*a Ultra High Strength Steel Welding Point
K108840

Foamed Sealing Material


Apply brushable seam seal on the inner bottom B-pillar foamed sealing material (1).


b.

Adjust and fix B-pillar reinforcement.


c.

Weld B-pillar reinforcement in the areas (2), (3) and (4).

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 8 mm (0.31 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




d.
K152894

Apply brushable seam seal on the foamed sealing material (1).


e.

Install the foamed sealing material (1).