Home › Vehicle Exterior › BODY PANEL › BACK DOOR
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402535 BACK DOOR F

BODY PANEL  BACK DOOR  PAINT REPAIR  


SUPPLY PARTS SPECIFICATION


K153313C01
4.563,1.75 4.708,1.552 4.708,1.552 4.875,1.552 true 3.573,0.552 3.417,0.25 3.417,0.25 3.25,0.25 false 2.833,0.833 3.083,1 3.083,1 3.25,1 true 3.073,0.167 3.385,0.323 0.313,0.156 10 false *3 3.292,0.917 3.51,1.083 0.219,0.167 10 false *2 4.927,1.479 5.24,1.635 0.313,0.156 10 false *1
*1 OUTER PANEL (unpainted) *2 INNER PANEL
*3 Glass adhesive line - -



POINTS TO CONSIDER WHEN PERFORMING BODY REPAIRS AND PAINTING


Replace the assembly in the following cases
·

The glass adhesive line on the substrate is exposed.

·

The inner panel is damaged.


Assembly replacement (supply part) Spot repair
Body repair - Be careful not to damage the glass adhesive line on the outer panel.

Assembly replacement (supply part) Spot repair
Masking
<Illustration 1>
The inner panel is unpainted. Therefore, make sure to properly apply masking tape to prevent paint from contacting the inner panel. Pay special attention to the edges.
Painting After painting the outer panel (after hardening), clean the glass adhesive line with cleaner R1.

<Illustration 1>

K153314C01
1.875,2.198 1.74,1.875 1.74,1.875 1.573,1.875 false 2.75,3.083 2.583,3.083 2.583,3.083 2.333,2.667 false 2,2.396 1.667,2.917 1.667,2.917 1.5,2.917 false 5.167,1.667 5,1.667 5,1.667 5.146,2.219 false 4.604,2.458 4.771,2.458 4.771,2.458 5.083,2.75 false 5.333,2.75 5.604,3 5.604,3 5.771,3 false 1.385,1.802 1.698,1.958 0.313,0.156 10 false *1 2.813,3.01 3.125,3.167 0.313,0.156 10 false *2 1.333,2.854 1.646,3.01 0.313,0.156 10 false *3 5.833,2.927 6.146,3.083 0.313,0.156 10 false *1 5.219,1.604 5.531,1.76 0.313,0.156 10 false *2 4.427,2.385 4.74,2.542 0.313,0.156 10 false *3
*1 OUTER PANEL *2 INNER PANEL
*3 MASKING TAPE - -



Assembly replacement (supply part) Spot repair
Painting and drying
<Illustration 2>
Back door condition Work method Drying temperature
Single - Secure it in the same position and condition as when it is installed on the vehicle, and support it so that the load is not concentrated in one area. (A)
NOTICE:

Take care when removing the glass as it is easily deformed.


HINT:

Support the panel at the hinge on the upper part of the panel and a secure location on the lower part of the panel.


80 °C or less
On-vehicle Fully closed None (B)
Half open Remove the left and right damper stays and secure them with the supports. (C)
Install the left and right damper stays and secure them with the supports. (D)
NOTICE:
·

The back door may twist due to the force of the damper stay. Therefore, do not perform work with only one damper stay removed.

·

Do not perform work with the glass removed as the back door may deform.



Fully open Remove the left and right damper stays and secure them with the supports. (E)
Left and right damper stays installed. (F)
NOTICE:
·

The back door may twist due to the force of the damper stay. Therefore, do not perform work with only one damper stay removed.

·

Do not perform work with the glass removed as the back door may deform.




<Illustration 2>

K153315N01
0.167,0.083 7,2.083 6.833,2 0.25,0.135 0.708,0.333 0.458,0.198 10 false (A) 0.083,2.167 0.542,2.365 0.458,0.198 10 false (B) 2.375,2.167 2.833,2.365 0.458,0.198 10 false (C) 4.667,2.167 5.125,2.365 0.458,0.198 10 false (D) 2.417,3.917 2.875,4.115 0.458,0.198 10 false (F) 0.083,3.917 0.542,4.115 0.458,0.198 10 false (E)