Home › Vehicle Exterior › BODY DIMENSIONS › FRONT DOOR
BM3650E _01 Vehicle Exterior _083398 BODY DIMENSIONS _0402542 FRONT DOOR F

BODY DIMENSIONS  FRONT DOOR  POINT-TO-POINT DISTANCE  


HINT:
·

Point D,d on the vehicle are asymmetrical.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Measuring Point Name
Symbol Name Hole Diameter
mm (in.)
A, a Inner screw point of dome-bulkhead-stiffening plate on upper section of bulkhead cross member M8 (0.31)
B, b Corner of front roof edge -
C, c Hole for mounting clip on A-pillar wiring harness φ6.5 (0.26)
D, d Hole for front inner seat cross member φ25 (0.98)
E, e Corner of tab on front carrier support -

K143695

Symmetric distance
K143696

Asymmetric distance

K151967C05
0.094,8.594 0.406,8.75 0.313,0.156 10 false *a
*a mm
(in.)
- -


Measuring Point Name
Symbol Name Hole Diameter
mm (in.)
A, a Weld nut for door brake connection M8 (0.31)
B, b Hole for sill trim mounting φ6 (0.24)
C, c Hole for sill trim mounting φ6 (0.24)
D, d Hole for expansion nut of A-pillar trim panel 7X7
(0.28X0.28)
E, e Hole for sill trim mounting φ6 (0.24)
F, f Threaded plate of lower lock striker M8 (0.31)
G, g Corner of rear upper door sill -
H, h Screw point of rear upper - front side panel holder φ8 (0.31)
J, j Screw point of rear lower - front side panel holder 10X10
(0.39X0.39)
K, k Screw point of front lower - front side panel holder 10X10
(0.39X0.39)

K151968C03
0.083,8.583 0.396,8.74 0.313,0.156 10 false *a 0.281,5.875 0.594,6.031 0.313,0.156 10 false *W 0.271,7.25 0.583,7.406 0.313,0.156 10 false *L 3.74,5.875 4.052,6.031 0.313,0.156 10 false *X
*a mm
(in.)
- -
*W Width distance *L Length distance
*X Diagonal distance - -


HINT:
·

Use point P when performing centering measurements for the body dimensions.

·

Point D,d E,e on the vehicle are asymmetrical.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Measuring Point Name
Symbol Name Hole Diameter
mm (in.)
A, a Weld nut for door brake connection M8 (0.31)
B, b Hole for sill trim mounting φ6 (0.24)
C, c Hole for sill trim mounting φ6 (0.24)
D, d Hole for sill trim mounting φ6 (0.24)
E, e Hole for front inner seat cross member φ25 (0.98)
F, f Corner of rear upper door sill -
G, g Attachment point of belt deflector support M10 (0.39)
H, h Hole for expansion nut of A-pillar trim panel 7X7
(0.28X0.28)
J, j Threaded plate of lower lock striker M8 (0.31)
K, k Mounting of upper support tube M8 (0.31)
P Tunnel hole - centre of vehicle φ25 (0.98)

K143695

Symmetric distance
K143696

Asymmetric distance

K151969C08
0.083,8.594 0.396,8.75 0.313,0.156 10 false *a 0.292,6.365 0.625,6.521 0.333,0.156 10 false *W 0.281,7.208 0.594,7.365 0.313,0.156 10 false *L 3.729,6.375 4.042,6.531 0.313,0.156 10 false *X
*a mm
(in.)
- -
*W Width distance *L Length distance
*X Diagonal distance - -