Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402558 FIT STANDARD / ADJUSTMENT METHOD F

BODY PANEL  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


Refer to the TOYOTA Repair Manual for adjustment method.

HINT:

Vehicle Exterior > DOOR / HATCH


INSPECT HOOD SUB-ASSEMBLY


HINT:
·

The dimensions stated in this document apply at an object temperature of 20°C (68°F).

·

The aim of adjustment is to achieve a uniform gap.

·

Symmetry of the gaps between left and right sides of the vehicle has top priority.

·

In terms of door gaps the maximum deviation between the front and rear door gap must be 1.0 mm (0.039 in.).

·

No gap dimension are specified for components which cannot be adjusted.



·
B506391C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Front Bumper Assembly


Gap dimension hood sub-assembly to front bumper assembly at center.

Standard Clearance:
Area Dimension
a 2.6 to 4.6 mm (0.102 to 0.181 in.)
b -0.5 to 2.5 mm (-0.020 to 0.098 in.)


·
B506392C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Headlight Assembly


Gap dimension hood sub-assembly to headlight assembly.

Standard Clearance:
Area Dimension
a 4.5 to 8.1 mm (0.177 to 0.319 in.)


·
B506393C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Front Bumper Assembly


Gap dimension hood sub-assembly to front bumper assembly at side.

Standard Clearance:
Area Dimension
a 2.6 to 6.4 mm (0.102 to 0.252 in.)
b 0.1 to 3.1 mm (0.004 to 0.122 in.)


·
B506394C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Front Side Panel


Gap dimension hood sub-assembly to front side panel.

Standard Clearance:
Area Dimension
a 3.1 to 5.9 mm (0.122 to 0.232 in.)
b 0.4 to 3.6 mm (0.016 to 0.142 in.)




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY


HINT:
·

The dimensions stated in this document apply at an object temperature of 20°C (68°F).

·

The aim of adjustment is to achieve a uniform gap.

·

Symmetry of the gaps between left and right sides of the vehicle has top priority.

·

In terms of door gaps the maximum deviation between the front and rear door gap must be 1.0 mm (0.039 in.).

·

No gap dimension are specified for components which cannot be adjusted.



·
B506395C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Front Door Panel Sub-assembly


Gap dimension hood sub-assembly to front door panel sub-assembly.

Standard Clearance:
Area Dimension
a 3.0 to 5.6 mm (0.118 to 0.220 in.)
b -0.7 to 1.7 mm (-0.028 to 0.067 in.)


·
B506396C02
0,0 0,0 false
(1) Front Side Panel
(2) Front Door Panel Sub-assembly


Gap dimension front side panel to front door panel sub-assembly.

Standard Clearance:
Area Dimension
a 3.3 to 5.3 mm (0.130 to 0.209 in.)
b -0.5 to 1.5 mm (-0.020 to 0.059 in.)


·
B506397C02
0,0 0,0 false
(1) Front Door Panel Sub-assembly
(2) Side Sill Trim Panel


Gap dimension front door panel sub-assembly to side sill trim panel.

Standard Clearance:
Area Dimension
a 2.5 to 5.1 mm (0.098 to 0.201 in.)
b -0.4 to 2.4 mm (-0.016 to 0.094 in.)


·
B506398C02
0,0 0,0 false
(1) Front Door Panel Sub-assembly
(2) Rear Side Panel


Gap dimension from front door panel sub-assembly to rear side panel.

Standard Clearance:
Area Dimension
a 2.8 to 4.8 mm (0.110 to 0.189 in.)
b -0.3 to 1.3 mm (-0.012 to 0.051 in.)




INSPECT BACK DOOR PANEL SUB-ASSEMBLY


CAUTION:
·

Shutting hood sub-assembly or back door panel sub-assembly.

Danger of injury!

-

Support hood sub-assembly / back door panel sub-assembly in fully open position with the aid of a suitable device.




a.
B506399C02
0,0 0,0 false
(1) Rear Side Panel
(2) Back Door Panel Sub-assembly


Check gap dimension of the rear side panel (1) for the back door panel sub-assembly (2).

Gap dimension rear side panel to back door panel sub-assembly:
Area Measurement
a 2.3 to 4.7 mm (0.091 to 0.185 in.)
b -1.5 to 0.9 mm (-0.059 to 0.035 in.)


i.

Gap dimension a does not correspond to the specifications.


ii.

Adjust back door panel sub-assembly on the back door hinge.


iii.

Dimension b does not correspond to the specifications.


iv.

Adjust the striker for the back door catch.



b.
B458650C02
0,0 0,0 false
(1) Roof Outer Skin
(2) Rear Window


Check gap dimension of the roof outer skin (1) for the rear window (2).

Gap dimension rear window to roof outer skin:
Area Measurement
a 5.8 to 9.1 mm (0.228 to 0.358 in.)
b 0.6 to 4.2 mm (0.024 to 0.165 in.)


i.

Gap dimension a does not correspond to the specifications.


ii.

Adjust back door panel sub-assembly on the back door hinge.


iii.

Dimension b does not correspond to the specifications.


iv.

Adjust back door hinge to body.



c.
B506400C02
0,0 0,0 false
(1) Back Door Panel Sub-assembly
(2) Rear Bumper Panel


Check gap dimension of the back door panel sub-assembly (1) for the rear bumper panel (2).

Gap dimension back door panel sub-assembly to rear bumper panel:
Area Measurement
a 3.6 to 6.6 mm (0.142 to 0.260 in.)
b 0.5 to 4.1 mm (0.020 to 0.161 in.)


i.

Gap dimension a does not correspond to the specifications.


ii.

Gap dimension a does not correspond to the specifications.


iii.

Dimension b does not correspond to the specifications.


iv.

Adjust back door panel sub-assembly to back door hinge.