Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
NM3650E _51 Engine / Hybrid System _081002 CRUISE CONTROL _0392293 CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  CRUISE CONTROL SYSTEM  CONTROL  CRUISE CONTROL  


SYSTEM CONTROL


a.

The cruise control function intervenes in the ECM and the transmission control ECU to maintain the selected speed. If necessary, the cruise control also intervenes in brake control. The function is integrated in the skid control ECU. Communication with the relevant partner control units is performed via the FlexRay bus.



FUNCTION


a.

Cruise control maintains a constant selected speed from approximately 30 to 250 km/h (19 to 155 mph). It offers the following additional functions compared to conventional cruise control.


b.

Active Brake Intervention

i.

If the engine drag torque is insufficient, in order to maintain the selected speed, a controlled brake intervention process automatically decelerates the vehicle further.



c.

Manual Gas Mode

i.

"Manual gas mode" enables the driver to constantly accelerate or decelerate in two corresponding dynamic stages via an operating control on the steering pad switch assembly. The requested speed is thus reached faster and the driver can accelerate or decelerate in the flow of traffic without having to assess the target speed in advance.



d.

Adapted Downhill Mode

i.

During controlled downhill driving, an overrun fuel cut-off is performed, as are adapted transmission downshifts. Appropriate measures to compensate for leaks and distribute torque between the front and rear axles are taken in the VSC brake control system with a virtual temperature model. This means any leak that does occur in the brake control circuit can be counteracted. The overrun fuel cut-off has a positive impact on fuel consumption. Downshifts and torque distribution relieve the strain on the wheel brake during downhill driving.




OPERATION


a.

If the function is active, a cruise control icon is shown on the combination meter assembly.


b.

The requested speed is shown on the combination meter assembly. The requested speed is shown during active control. If the cruise control function is in "standby" mode, then the most recently used requested speed is displayed in grey. After the cruise control function has been activated or the requested speed has been readjusted, the updated digital value is shown.


c.

When the function is active, the indicators are shown in green. In standby mode, the indicators are grey.


d.

When control is active, this is indicated on the headup display (meter mirror sub-assembly) too. (Models with headup display)

Combination Meter Assembly
Y237939C01
2.615,3.375 2.927,3.531 0.313,0.156 10 false *a 4.396,3.365 4.708,3.521 0.313,0.156 10 false *b 0.198,3.521 0.51,3.677 0.313,0.156 10 false *c
*a Active/Overdriven *b Standby
*c The illustrations shown are examples only. - -


Headup Display (Meter Mirror Sub-assembly) (Models with Headup Display)
Y237940C01
2.24,2.021 2.552,2.177 0.313,0.156 10 false *a 4.656,2.021 4.969,2.177 0.313,0.156 10 false *b 0.167,2.531 0.479,2.688 0.313,0.156 10 false *c
*a Active/Overdriven *b Standby
*c The illustrations shown are examples only. - -



e.

The function is operated via a steering pad switch assembly on the left-hand steering wheel spoke. Pressing the DCC switch activates the cruise control function and the current driving speed is maintained.


f.

When the function is active, the cruise control can be interrupted by pressing the CNCL switch. The speed will now no longer be maintained. By pressing the brake pedal, the function is also interrupted.


g.

If the system is interrupted, the driver can reactivate the cruise control function from a speed of 30 km/h (19 mph) by pressing the RES switch and the stored speed is regulated again. Pressing the "SET" switch (country-dependent) or actuating the vehicle speed select switch will adopt the current speed as the requested speed. When the system is active, the requested speed can be changed at will in increments of 1 or 10 km/h or 1 or 5 mph.


h.

Pressing the DCC switch when the system is active or interrupted will switch it off.


i.

The driver is always able to override the cruise control requirements and accelerate more sharply by pressing the accelerator pedal. This does not deactivate the system.

Y237938C01
2.583,2.406 2.75,2.406 2.75,2.406 3,1.99 true 2.667,0.594 2.833,0.594 2.833,0.594 3.083,1.01 true 2.458,1 2.625,1 2.625,1 2.875,1.417 true 3.667,0.917 3.917,0.5 3.917,0.5 4.083,0.5 true 3.781,1.354 4.198,0.938 4.198,0.938 4.365,0.938 true 4.156,0.385 4.469,0.542 0.313,0.156 10 false *a 4.438,0.833 4.75,0.99 0.313,0.156 10 false *b 2.479,0.479 2.792,0.635 0.313,0.156 10 false *c 2.26,0.896 2.573,1.052 0.313,0.156 10 false *d 2.396,2.292 2.708,2.448 0.313,0.156 10 false *e
*a DCC Switch *b Vehicle Speed Select Switch
*c RES Switch *d CNCL Switch
*e SET Switch - -