Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM
NM3650E _51 Engine / Hybrid System _081002 CRUISE CONTROL _0392865 DYNAMIC RADAR CRUISE CONTROL SYSTEM CO CONTROL F

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  CONTROL  DYNAMIC RADAR CRUISE CONTROL  


SYSTEM CONTROL


a.

The adaptive cruise control with stop&go function can be set to speeds within a speed range from 30 km/h (19 mph) to 160 km/h (99 mph), and can also maintain the vehicle-to-vehicle following distance. The selected following distance is also maintained in slow-moving traffic and traffic jams right down to a standstill. Depending on the idle time, automatic or driver initiated controlled drive-off from a standstill is available.


b.

To use cruise control without a distance control component, the standard cruise control function is available in the speed range above 30 km/h (19 mph).


c.

The adaptive cruise control with stop&go function also responds when the preceding vehicle is stopped, and applies the brakes until this vehicle stops.


d.

The distance information function is used to alert the driver if the vehicle-to-vehicle following distance between this vehicle and the preceding vehicle falls to less than a specified minimum distance. The distance from the preceding vehicle is measured by the millimeter wave radar sensor (laser radar sensor). The vehicle-to-vehicle following distance is judged based on the time gap with the preceding vehicle, and if this time gap falls below the limit value, a warning is displayed in the headup display (meter mirror sub-assembly). The distance information function can be activated and deactivated. (Models with headup display)



FUNCTION


a.

When a preceding vehicle is detected in your lane and your vehicle approaches it, the system gradually adjusts the speed according to the speed of the preceding vehicle. After that, a following distance selected by the driver is constantly maintained. If the system detects the preceding vehicle has stopped, it applies the brakes until your vehicle stops at the specified vehicle-to-vehicle distance.


b.

If the preceding vehicle begins moving after a brief period, your vehicle will also start moving automatically (without any driver input). If the stationary period is longer, the vehicle can be made to start moving by operating the steering pad switch assembly or depressing the accelerator pedal.


c.

If the driver leaves the vehicle while it is stopped and the system is active, the electric parking brake operates to keep the vehicle stopped.


d.

The selected following distance and selected vehicle speed are maintained via coordinated control of the engine and the brake control systems. Brake control varies according to vehicle speed, and brakes are applied more strongly at low speeds due to traffic dynamics. At higher speeds, brake control gives priority to comfortable, gradual braking. However, when sudden deceleration is required, the visual and audio warnings are used to alert the driver.


e.

Distance information display function (Models with headup display)

i.

When the distance from the preceding vehicle becomes less than the set value, a warning icon is displayed in the headup display (meter mirror sub-assembly).


ii.

The function can be activated and deactivated in the settings menu for the headup display (meter mirror sub-assembly).

Y237954




OPERATION


a.

The requested speed is still shown in the combination meter assembly.


b.

This speed is shown in green during active control periods. When the system is in standby mode, the requested speed is displayed in grey. After the system has been reactivated or the set speed has been readjusted, the vehicle-to-vehicle following distance level and preceding vehicle are displayed.


c.

If the system is no longer able to adjust the vehicle to a safe distance due to very high differential speeds, for example, a flashing vehicle symbol and an acoustic signal prompt the driver to take over full control of the vehicle again.


d.

When the vehicle has been stopped by automatic control, the display informs the driver that the preceding vehicle has started to move again. However, for safety reasons the vehicle remains stopped. These indicators are also shown on the headup display (meter mirror sub-assembly)*.

*: Models with headup display


Y237957C01
1.448,2.063 1.76,2.219 0.313,0.156 10 false *a 2.781,2.063 3.094,2.219 0.313,0.156 10 false *b 4.146,2.063 4.458,2.219 0.313,0.156 10 false *c 5.5,2.063 5.813,2.219 0.313,0.156 10 false *d 1.448,4.406 1.76,4.563 0.313,0.156 10 false *e 2.792,4.406 3.104,4.563 0.313,0.156 10 false *f 4.146,4.406 4.458,4.563 0.313,0.156 10 false *g 5.5,4.406 5.813,4.563 0.313,0.156 10 false *h 0.167,4.563 0.479,4.719 0.313,0.156 10 false *i
*a System Active *b Accelerating
*c Standby *d Stopped
*e Stopped, Preceding Vehicle Started Moving *f Distance to Preceding Vehicle Below Limit (Flashing)
*g Braking (Flashing) *h No Preceding Vehicle
*i The illustrations shown are examples only. - -



e.

This function is operated via the steering pad switch assembly. Pressing the ACC switch activates the system and the current vehicle speed is maintained as the set speed. This is limited to the permitted range between 30 and 160 km/h (19 and 99 mph).


f.

When the system is active, it can be interrupted by pressing the RES/CNCL switch. Distance and speed are then no longer maintained. The requested speed is then displayed in grey.


g.

If the system is in standby mode, the system can be reactivated by pressing the RES/CNCL switch, and the saved speed is maintained as the requested speed. If the function is reactivated using the SET switch, the current speed is adopted as the requested speed. When the system is active, the requested speed can be adjusted in increments of 1 or 10 km/h (0.6 or 6 mph) within the permitted range. A vehicle-to-vehicle distance select switch allows the driver to select the following distance from 4 levels. The most recently used following distance is stored.


h.

The switch can be deactivated by pressing the ACC switch.


i.

For safety reasons, when the vehicle is stationary the function can only be put in standby mode or deactivated when the brake pedal is also pressed at the same time.


j.

While driving, the system is deactivated by pressing the brake pedal.


k.

The driver is always able to override the system and accelerate more sharply by pressing the accelerator pedal. This does not deactivate the system.

Y237955C01
3.792,1.365 4.5,0.833 4.5,0.833 4.667,0.833 true 3.667,0.917 4.021,0.333 4.021,0.333 4.188,0.333 true 2.656,0.635 2.823,0.635 2.823,0.635 3.073,1.052 true 2.5,1 2.667,1 2.667,1 2.917,1.417 true 2.583,2.417 2.75,2.417 2.75,2.417 3,2 true 4.26,0.25 4.573,0.406 0.313,0.156 10 false *a 4.74,0.75 5.052,0.906 0.313,0.156 10 false *b 2.448,0.542 2.76,0.698 0.313,0.156 10 false *c 2.292,0.917 2.604,1.073 0.313,0.156 10 false *d 2.375,2.323 2.688,2.479 0.313,0.156 10 false *e
*a ACC Switch *b Vehicle Speed Select Switch
*c Vehicle-to-vehicle Distance Select Switch *d RES/CNCL Switch
*e SET Switch - -