Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
NM3650E _58 Vehicle Interior _081837 SUPPLEMENTAL RESTRAINT SYSTEMS _0395495 AIRBAG SYSTEM DE DETAILS F

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DETAILS  AIRBAG ECU ASSEMBLY  


FUNCTION


a.

The airbag ECU assembly has the following tasks:

i.

Detecting an accident situation that is critical for the occupants


ii.

Activating the necessary restraint systems (selectively depending on the severity of the accident and accident type)



b.

The airbag ECU assembly with integrated sensor system calculates the following variables, for example for the impact detection:

i.

Longitudinal acceleration and vehicle inclination in longitudinal direction


ii.

Lateral acceleration and vehicle inclination in transverse direction


iii.

Yaw rate (rotation about the vertical axis)


iv.

Roll rate (rotation around the longitudinal axis)



c.

If the PAD mode (testing-analysis-diagnosis) is activated, the airbag ECU assembly starts a self-test.

i.

During this time, the airbag indicator light lights up (approx. 3 to 5 seconds). When the safety system is functional, the airbag warning light goes out.



d.

All the gas generators and sensors in the safety systems are directly connected with the airbag ECU assembly.


e.

The airbag ECU assembly evaluates the acceleration data (longitudinal and lateral acceleration) of the sensors and thus determines the direction and severity of the accident in the event of a crash.


f.

Comprehensive tests are used to define triggering thresholds for all possible types of accident.

i.

This results in different trigger thresholds for activation of the various restraining systems (airbags, belt tensioner, etc.).



g.

In the event of a crash, the airbag ECU assembly determines whether activation is required and which gas generators (belt tensioner, airbags, etc.) should be ignited.


h.

In vehicles with a combustion engine, the airbag ECU assembly deactivates the electric fuel pump.

i.

The airbag ECU assembly also triggers the safety battery terminal.



i.

The restraint systems are triggered only when 2 independent sensors detect the corresponding threshold.

i.

The airbag ECU assembly transmits a message to other bus users when the restraint systems are triggered.



j.

The individual control units execute various functions according to the severity of the accident.

i.

For instance, the main body ECU (multiplex network body ECU) switches on the interior lights and the hazard warning flashers.



k.

The airbag ECU assembly transmits a signal to the Telematics Communication Box through a direct line.

i.

The Telematics Communication Box then automatically transmits an emergency call that includes the location of the vehicle.



l.

When the restraint systems are activated, certain data is written to a read-only data memory in the airbag ECU assembly.

i.

The data is relevant to accident research (no access for service).


ii.

After 3 crash signals, the data memory is full. The airbag warning light lights up. The airbag ECU assembly must be replaced.

·

The airbag warning light lights up.

·

The airbag ECU assembly must be replaced.




m.

For the seat belt warning, the signals of the belt buckle switch are picked up separately.


n.

The airbag ECU assembly contains an ignition capacitor.

i.

If the voltage supply is interrupted in the event of a crash, the ignition capacitor acts as an energy reserve for the airbag ECU assembly.

Y245343C03
2.083,1.333 1.583,0.5 1.583,0.5 1.417,0.5 true 1.219,0.417 1.531,0.573 0.313,0.156 10 false *1
*1 Airbag ECU Assembly - -




o.

The airbag ECU assembly is connected to the vehicle electrical system by means of the connector.


p.

Communication of the airbag ECU assembly with the relevant partner control units is performed via the FlexRay bus.


q.

The right front power distribution box supplies power to the airbag ECU assembly via terminal.


r.

In addition to all the inputs and outputs, the airbag ECU assembly also monitors the internal components (self-test).

i.

Possible fault codes are stored in the airbag ECU assembly.


ii.

In the event of a system error or a fault in a component, the airbag warning light lights up.



s.

In the event of an internal malfunction of the airbag ECU assembly or in the voltage supply, the entire safety system is disabled.