Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM
NM3650E _58 Vehicle Interior _081838 PRE-COLLISION _0395496 PRE-COLLISION SYSTEM CO CONTROL F

PRE-COLLISION  PRE-COLLISION SYSTEM  CONTROL  PRE-COLLISION CONTROL  


FUNCTION


a.

The collision warning with braking function and pedestrian warning with city braking function operate when there is a risk of collision with a vehicle, pedestrian or bicycle. The operation speeds for each control are as follows.

Operation Speed
The Vehicle Models with Millimeter Wave Radar Sensor Assembly Models without Millimeter Wave Radar Sensor Assembly
Vehicle Approximately 5 to 250 km/h (3 to 155 mph) Approximately 5 to 85 km/h (3 to 53 mph)
Cyclists/pedestrian Approximately 5 to 85 km/h (3 to 53 mph) Approximately 5 to 85 km/h (3 to 53 mph)


b.

In the following situations, the collision warning with braking function and pedestrian warning with city braking function may be restricted.

i.

During heavy fog, rain or snow fall.


ii.

Sharp corners.


iii.

The driving stability control system is OFF.

·

VSC OFF etc.



iv.

The surveillance area of the camera or the windshield in front of the room mirror is dirty.


v.

The camera is overheated due to temperature and has been temporarily turned off.


vi.

The radar sensor is dirty or covered.


vii.

Within 10 seconds of starting the engine using the start/stop button.


viii.

While the camera is being corrected right after delivery.


ix.

The glare, such as due to low-lying sun, is constantly projected on the vehicle.


x.

It is dark. *

*: Pedestrian warning with City braking function




c.

The indicators for front collision warning with brake function have been provided in the combination meter assembly and on the headup display to issue the pre-warning and acute warning.

i.

An acute warning is issued by flashing the indicator and sounding an audible warning.


ii.

When this setting is set to late, the brakes will not be controlled.


iii.

The braking is terminated when the driver depresses the accelerator pedal or by intentionally maneuvering the steering wheel.


iv.

The front collision warning with braking function may not detect correctly in cases such as the following.

·

When approaching the low speed driving vehicle in the front with high speeds.

·

Vehicle that suddenly cuts in or abruptly decelerates

·

A vehicle with a strange rear appearance

·

A 2 wheel vehicle ahead

Y245325C03
2.583,0.417 2.75,0.417 2.75,0.417 3.167,0.833 true 2.385,0.333 2.698,0.49 0.313,0.156 10 false *1
*1 Front Collision Warning Indicator - -





d.

The indicators for pedestrian warning with brake function have been provided in the combination meter assembly and on the headup display to issue the pre-warning and acute warning.

i.

An acute warning is issued by flashing the indicator and sounding an audible warning.


ii.

When this setting is set to late, the brakes will not be controlled.


iii.

The braking is terminated when the driver depresses the accelerator pedal or by intentionally maneuvering the steering wheel.

Y245326C03
2.583,0.417 2.75,0.417 2.75,0.417 3.5,0.75 true 2.385,0.333 2.698,0.49 0.313,0.156 10 false *1
*1 Pedestrian Collision Warning Indicator - -



iv.

The detection range of the pedestrian warning with city brake function in front of the vehicle can be divided into the following 2 parts.

·

Center area (arrow 1), straight ahead of the vehicle

·

Expansion range (arrow 2), right and left hand areas of the center area



v.

If there is any pedestrian in the center area, there is a danger of collision. As for a pedestrian in the expansion range, this warning is issued only when the pedestrian moves toward the center area.

Y245327


vi.

The pedestrian warning with city braking function may not detect correctly in cases such as the following.

·

Partially concealed pedestrian.

·

Pedestrian not recognized correctly due to the angle of the camera or the shape.

·

Pedestrian outside the detection range

·

Pedestrian with a body height of shorter than approximately 80 cm (31.50 in)