SYSTEM CONTROL
The blind spot monitor system performs the following controls.
Vehicle outside of the sensor's detection range: Indicator will not light up.
| *1 | Approaching vehicle | *2 | Own vehicle |
| *a | Detection range | *b | Areas that are not visible using the outside rear view mirrors (the blind spots) |
| *c | The illustration shown is an image only. | - | - |
Slowly approaching vehicle inside the sensor's detection range: Indicator will not turn on.
| *1 | Approaching vehicle | *2 | Own vehicle |
| *a | Detection range | *b | Areas that are not visible using the outside rear view mirrors (the blind spots) |
| *c | The illustration shown is an image only. | - | - |
Fast approaching vehicle inside the sensor's detection range: LED warning indicator on the detected side lights up.
| *1 | Approaching vehicle | *2 | Own vehicle |
| *3 | Outside rear view mirror | - | - |
| *a | Detection range | *b | Areas that are not visible using the outside rear view mirrors (the blind spots) |
| *c | Indicator | *d | The illustration shown is an image only. |
Fast approaching vehicle inside the sensor's detection range and the turn signal lever is operated toward the detected side: The steering wheel vibrates and the indicator on the detected side flashes.
| *1 | Approaching vehicle | *2 | Own vehicle |
| *3 | Outside rear view mirror | *4 | Steering wheel |
| *a | Detection range | *b | Areas that are not visible using the outside rear view mirrors (the blind spots) |
| *c | Indicator | *d | The illustration shown is an image only. |
When a vehicle is detected in a blind spot of the outside rear view mirrors and the turn signal lever is operated toward the detected side: The steering wheel vibrates and the indicator on the detected side flashes.
| *1 | Approaching vehicle | *2 | Own vehicle |
| *3 | Outside rear view mirror | *4 | Steering wheel |
| *a | Detection range | *b | Areas that are not visible using the outside rear view mirrors (the blind spots) |
| *c | Indicator | *d | The illustration shown is an image only. |
FUNCTION
Operating Condition
Lane change warning activates at the vehicle speeds of 30 km/h (19 mph) or higher (when lane is not recognized) and at 60 km/h (37 mph) or higher (when lane is recognized).
The rear crossing traffic alert (RCTA) activates at the vehicle speed of 0 to approximately 7 km/h (4 mph) when the rear view camera is displayed or the shift lever is engaged in R.
Lane Change Warning Detection Range
Lane Change Warning Detection Range
Rear crossing Traffic Alert Detection Function
The rear crossing traffic alert sets off a warning when time to collision for RCTA is approximately 2 seconds or less.
Lane Change Warning Function
The lane change warning warns the driver of the vehicle in the blind spot or of the vehicle approaching from behind at high speeds by illuminating the indicator on the outer rear view mirror.
If the turn indicator is operated on the illuminated indicator side, warning is set off by flashing the indicator and the steering wheel vibration.
Rear Crossing Traffic Alert Warning Function
Rear crossing traffic alert warning has two stages and consists of the following components:
Information level (vehicle parked or moving): RCTA warning shown in the PDC screen area.
Acute level (vehicle moves in the respective direction): Warning sound emitted from the vehicle speakers and activation of the indicators on the outside rear view mirror.
| *a | Detection range | *b | The illustration shown is an image only. |
Brightness Control Function
The brightness of the indicators on the outer rear view mirrors can be adjusted in synchronization with the combination meter assembly lights by the rheostat in the instrument panel.
Initial Check Function
When unlocking the vehicle doors, the indicators on the outer rear view mirror assemblies are flashed for a short period and the initial check of the system is performed.
Sensitivity Adjusting Function
The warning timing can be set to early/average/late in the menu with the "lane change warning" set point via Toyota Supra Command.
Lane Change Warning OFF Function
The lane change warning can be deactivated by the safety system switch on the upper surface of the center cluster.
The functions, such as all safety systems, only the lane change warning, etc., can be activated or deactivated via Toyota Supra Command.