Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
NM3650E _59 Vehicle Exterior _082877 WINDOW / GLASS _0399814 POWER WINDOW CONTROL SYSTEM CO CONTROL F

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  CONTROL  POWER WINDOW CONTROL  


FUNCTION


a.

Opening the Windows

i.

Press the switch to the first stop position. The window opens while the switch is being held to the designated position.


ii.

Press the switch past the first stop position. The window opens automatically. Pressing the switch again stops the window movement.



b.

Closing the Window

i.

Pull the switch to the first stop position. The window continues to close as long as the switch is held to the designated position.


ii.

Pull the switch past the first stop position. The window closes automatically. Pressing the switch again stops the window movement.



c.

Anti-trap Mechanism

i.

The anti-trap mechanism is active over the entire window movement range in the closing direction. The anti-trapping mechanism is not a system for preventing entrapment entirely, but rather one that limits the maximum permitted closing force. The anti-trap function is only enabled once the power windows have been successfully initialized and automatic closing is possible. The mechanical forces for the closing procedure vary according to ambient temperature and component wear. Consequently, the closing force is re-learned each time the sunroof closes, so that the anti-trap function can adjust accordingly.



d.

Key-off Operation

i.

After IG OFF, the power windows can be operated for an additional 1 minute. The power windows cannot be operated if one of the front doors is open. The windows can be opened and closed using the following control units:

·

Power Window Regulator Master Switch Assembly

·

Power Window Regulator Switch Assembly

·

Remote Key

·

Driver Seat Door Lock





e.

One-touch Function

i.

When opening or closing using the one-touch function, the Power Window Regulator Motor Assembly operates at increased speed. The opening and closing operations of the one-touch function are only available when the anti-trap function is active. To ensure that the windows are securely closed, the Power Window Regulator Motor Assembly is briefly driven in the blocking condition (mechanical end stop) at the upper end stop position.



f.

Emergency Close

i.

Emergency closing is for intentional closing of the windows with the anti-trap mechanism. To do this, the power window switch must be pulled and continuously held in that position. This function may be needed in the event of an attack or if the windows are mechanically jammed or frozen in place.


ii.

Emergency closing can be activated at a speed of up to 16 km/h.


iii.

Releasing the power window switch will interrupt the function.



g.

Panic Mode

i.

The panic mode can only be triggered after emergency closing has been performed. In the event of blocking, the Power Window Regulator Motor Assembly is supplied with current until the overheating protection is activated.


ii.

If the user releases and then presses and holds the power window switch within four seconds, the window is closed without the anti-trap mechanism. The window is then closed with maximum force and speed.


iii.

The windows can be opened at any time, even if the thermal switch has tripped. Releasing the power window switch will interrupt the function.



h.

Repeat Lock

i.

A repeat lock is provided for each motor to prevent the Power Window Regulator Motor Assembly from overheating.


ii.

The operating time for the Power Window Regulator Motor Assembly is limited. The motor is switched off for a defined time.


iii.

The repeat lock allows the window to travel through at least five complete motion processes (opening and closing), with the last operation being a closing operation.


iv.

If something becomes trapped, the repeat lock will not prevent the window from opening. The anti-trap mechanism is always able to reverse the movement of the window.



i.

Power Saving

i.

To protect the battery, the power windows do not operate while the engine is being started, and any ongoing functions of the power windows are halted. If the battery voltage falls below 9 volts, the Power Window Regulator Motor Assembly is switched off.



j.

Initializing the Power Windows

i.

During power window initialization, two parameters are learned by the control unit: the upper end stop (power window normalizing) and the power characteristic curve for opening and closing.

Preconditions
·

Ambient temperature is 15°C or more

·

Vehicle is stationary

·

Battery has sufficient voltage, charger is connected if necessary.

·

PAD mode is switched on

·

All doors are closed




ii.

Erasing Initialization Data and Re-initializing Power Windows

·

Deleting initialization data and then re-initializing can remedy sporadic incorrect shut-downs in power window automatic mode (one-touch mode).

Erasing Initialization Data
·

Fully open the window in the appropriate door.

·

Press the switch all the way down (switch position for automatic operation), maintaining pressure for longer than 15 seconds, but less than 20 seconds.

·

The deletion of the initialization data was successful if the window functions no longer operate in automatic mode (one-touch mode).



Performing Initialization
·

Fully close the window by pulling the switch so that the top end stop is reached.

·

The switch must remain pulled continuously during this procedure.

·

The power window is initialized when the top end stop is reached.

·

The initialization was successful if the window can be opened and closed without any problems in automatic mode (one-touch mode).