FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
| Engine Switch (Push Start Switch) | Starts or stops the engine when pressed. |
| Stop and Start System Cancel Switch | ·
Pressing the switch turns the auto start/stop off. ·
When the engine is manually restarted, the auto start/stop will be reactivated. |
| Starter Assembly | ·
Rotates the crankshaft in the engine up to the speed necessary to start the engine (starting speed). ·
For the auto start/stop, a reinforced starter motor is used to handle the higher frequency of operation. |
| Generator Assembly | A high-performance generator has been adopted to compensate for battery drain during idling stop. |
| Battery | An AGM battery with high charge-discharge cycle durability has been adopted. |
| Hood Lock Assembly | Detects the opening and closing of the engine hood. |
| Front Seat Inner Belt Assembly (Driver) | Detects whether the driver seat seatbelt is fastened. |
| Front Door Lock with Motor Assembly (Driver) | Detects whether the driver door is open or closed. |
| ECM | Controls the auto start/stop. |
SYSTEM CONTROL
Idling Stop Control
Except when idling stop operation is prohibited, idling stop control is performed when all of the following conditions are met:
Vehicle is stationary. (Vehicle speed is below 3 km/h (2 mph).)
Shift selector lever is in the D position.
The brake pedal is being depressed.
Engine Start Control
During idling stop control, the engine restarts when one of the following conditions is met:
The brake pedal is released.
The accelerator pedal is operated.
Selector lever is moved from P to D position.
Selector lever is moved from D to N or R position.
The battery state of charge is too low.
The ambient temperature is above 35°C (95°F) with the heating and air conditioning system switched on.
The condensation sensor detects condensation on the windshield.
The evaporator temperature is too low to ensure sufficient climate control.
Special case: the driver's seat belt is still fastened, the driver's door is opened and the brake pedal is released.
Idling Stop Prohibition Control
In the following conditions, idling stop operation is prohibited:
The ambient temperature is above 35°C (95°F) with the heating and air conditioning system switched on.
The brake pedal is not pressed firmly enough which means the vehicle is detected as not being held sufficiently.
The vehicle stops on sharp uphill/downhill gradients.
The steering wheel angle is too big.
The vehicle has not been driven at a speed of 3 km/h (2 mph) following the previous engine shutdown.
The engine is not running at idle speed. (Accelerator pedal is being pressed.)
The vehicle is reversing.
The operating temperature of the engine is too low.
The oil volume reservoir is not yet charged.
In stop-and-go traffic.
Selector lever is in the N or R position.
The condensation sensor detects condensation on the windshield.
The battery state of charge is too low.
Auto Start/Stop Deactivated
If a deactivation condition exists, the auto start/stop is deactivated. The following scenarios arise, depending on when the deactivation condition for the auto start/stop occurred:
The engine continues running and is no longer stopped automatically.
The engine was stopped automatically and starts once again automatically.
The engine was automatically shut down and no longer starts automatically (a message for the manual start appears in the combination meter assembly).
The following deactivators may occur:
The driver's absence has been detected.
The hood lock assembly is unlocked.
A fault related to the auto start/stop has been detected at the engine, transmission or components involved in the auto start/stop.
The bus communication is faulty.
The auto start/stop has been deactivated via the stop and start system cancel switch.
The auto start/stop was deactivated via the diagnosis system.
The engine was shut down due to insufficient speed.
FUNCTION
Limitations of Auto Start/Stop
On a vehicle in which the auto start/stop is operating to reduce fuel consumption and CO2 emissions, the power supply management needs to be monitored during idling stop control. If the battery charge condition is low, prevention of switch-off (idling stop prevented) or request for switch-on (immediate engine start) will occur. This allows the vehicle starting characteristics to be retained.
Power Management
Power management is the system that manages the power supply. Power management is controlled by the ECM.
Power management controls the output requests for power needed to start up high-current devices, the generator output, and the battery charge level while driving.
The objective of power management is to ensure reliable engine starting by managing the power supply after idling stop is performed. This ensures that engine starting and stopping by the auto start/stop can be performed reliably and repeatedly.
It is necessary to avoid high current consumption during idling stop operation. While the engine is stopped by idling stop control, the power management system avoids high current loads from the following system, thereby saving fuel.
Rear Defogger
Mirror Heater
Seat Heater (Models with seat heater)
Blower
During idling stop control by the auto start/stop, if the battery charge level decreases below a certain level, the engine will restart automatically without any intervention from the driver.