Home › Drivetrain › 8HP51 (AUTOMATIC TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
NM3650E _52 Drivetrain _082979 8HP51 AUTOMATIC TRANSMISSION / TRANSAXLE _0400269 ELECTRONIC SHIFT LEVER SYSTEM CO CONTROL F

8HP51 AUTOMATIC TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  CONTROL  SHIFT CONTROL  


SYSTEM CONTROL


a.

The transmission floor shift assembly consists of the control electronics circuit and the selector lever. The sensors for detecting the gearshift lever position and for inhibiting inadvertent gearshifts are integrated in the control electronics.


b.

The engaged shift position is shown on the function display regardless of the selector lever position.


c.

The following positions can be selected with the selector lever:

i.

P: for Park. "P" is set using a dedicated switch on the selector lever.


ii.

R: for Reverse gear


iii.

N: for Neutral


iv.

D: for Drive = automatic mode


v.

M: for Manual mode



d.

The selected shift position is indicated by LEDs in the shift pattern located on the surface of the selector lever. The shift pattern is only displayed if the transmission control ECU has implemented the driver's choice and has reported this state to the transmission floor shift assembly via the bus. The transmission floor shift assembly only displays what it has received from the transmission control ECU.


e.

The selector lever position of the transmission floor shift assembly is detected by means of non-contact Hall-effect sensors and sent via communication bus to the transmission control ECU.

X134056C01
1.833,1.25 2,1.25 2,1.25 2.25,1.667 true 4.948,2.052 5.365,2.469 5.365,2.469 5.531,2.469 true 4.094,1.99 4.26,1.99 4.26,1.99 4.51,1.74 true 4.938,1.25 5.271,0.917 5.271,0.917 5.438,0.917 true 1.667,1.135 1.979,1.292 0.313,0.156 10 false *1 5.51,0.813 5.823,0.969 0.313,0.156 10 false *2 5.604,2.365 5.917,2.521 0.313,0.156 10 false *3 3.885,1.885 4.198,2.042 0.313,0.156 10 false *4 3.885,0.781 4.198,0.938 0.313,0.156 10 false *5 0.229,3.469 0.542,3.625 0.313,0.156 10 false *a
*1 Transmission Floor Shift Assembly *2 P Button (Parking)
*3 Function Display with Shift Pattern *4 Selector Lever Lock
*5 Selector Lever - -
*a The illustrations shown are examples only. - -




FUNCTION


a.

Selecting a Shift Position

i.

To engage a shift position after engine start-up, the selector lever must be pushed / pushed and held backwards or forwards. To shift to the R position, in addition to operating the brakes, the selector lever lock on the side of the selector lever must also be pressed. The selector lever "P" position is selected from the shift pattern using the dedicated operation switch on the transmission floor shift assembly. From the selector lever "D" position, the driver can manually change over to the manual mode (selector lever "M" position) at any time.



b.

Automatic Reset

i.

If the P button is pressed or the parking lock is automatically engaged by the ignition and the selector lever switch is still in the manual mode (selector lever "M" position), the selector lever is reset from the manual mode (selector lever "M" position) to the automatic mode (selector lever "D" position).



c.

Memory Function for Driving Direction Change

i.

When the driver attempts to change the selector lever position from "D" to "R" or from "R" to "D":

·

When driving at less than 5 km/h (3 mph): The driver's choice is implemented by the transmission control ECU.

·

When driving at 5 km/h (3 mph) to 10 km/h (6 mph): The selector lever "N" position is engaged by the transmission control ECU. The display of the engaged drive position changes to the one that the driver has just chosen, either the selector lever "D" position or the selector lever "R" position. The driver's choice is stored. If the vehicle's speed drops below 5 km/h (3 mph) within 1 second, the driver's wish for selector lever "D" position or selector lever "R" position is carried out by the transmission control ECU. If this speed is not undershot, the selector lever position remains in "N" and the display switches to "N".

·

When driving at 10 km/h (6 mph) or more: The selector lever "N" position is engaged by the transmission control ECU.




d.

Memory Function for Parking Lock

i.

When the driver attempts to change the selector lever position to "P" (Parking lock):

·

When driving at less than 2 km/h (1 mph): The selector lever "P" position is engaged by the transmission control ECU.

·

When driving at 2 km/h (1 mph) to 5 km/h (3 mph): The current selector lever position remains, and the driver's choice is stored. If a speed of 2 km/h (1 mph) is undershot within 1 second, the selector lever "P" position is engaged by the transmission control ECU.

·

When driving at 5 km/h (3 mph) or more: The driver's choice is not accepted. The current selector lever position remains. At the same time, a warning message is displayed.




e.

Hold Time of Selector Lever "N" Position

i.

At a vehicle speed of less than 2 km/h (1 mph) with the engine off:

·

When the selector lever "N" position is engaged, the 30-minute hold time of the selector lever "N" position begins. The functional display remains on and the selector lever "N" position illuminates in the shift pattern.

·

At the end of the hold time of the selector lever "N" position, the display flashes. The transmission control ECU engages the selector lever "P" position after a further 10 seconds.

·

If the selector lever is moved during the hold time, the 30 minute period starts again from the beginning.