SYSTEM CONTROL
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | The ABS prevents the wheels from locking when braking. The brake pressure is controlled on all the wheels in such a way that each wheel runs in an optimal slip range. The slip is optimally adjusted so that the highest possible braking and cornering forces can be transferred. |
| Cornering Brake Control (CBC) | The CBC is an extension of the ABS, which increases driving stability when braking. Shifting of the wheel loads when cornering can lead to reduced driving stability and turning performance when braking. The CBC acts against this and generates a stabilizing counter-torque via a single-sided build up of the brake pressure by slightly braking outside of the ABS control range. |
| Electronic Brake Force Distribution (EBV) | To prevent over-braking of the rear wheels in certain situations, the electronic brake force distribution (EBV) continually monitors the front and rear wheel slip values and adjusts the braking force on the rear wheels in relation to the front wheels. |
| Automatic Stability Control (ASC) | The ASC ensures the best possible driving stability by preventing free spinning of the drive wheels, e.g. when accelerating. If one wheel of the powered axle is on a non-slip surface and the other is on a slippery surface, the wheel that is slipping is slowed down to prevent it from spinning until the other drive wheel can transfer driving power to the road surface again. The ASC can also intervene in the engine control through cross-linking via data bus systems. |
| Engine Drag Torque Control (MSR) | The engine drag torque control (MSR) prevents the rear wheels from locking on slippery driving surfaces when downshifting or abruptly releasing the accelerator. The MSR immediately detects the locking upon its emergence via the wheel speed sensors and momentarily reduces the engine drag torque by slightly accelerating. The drive wheels thereby also maintain their cornering forces during coastdown. |
| Brake Assistant | During panic braking, the brake assistant generates powerful braking force independently of the driver's pedal operation. When the brake pedal is quickly depressed, the brake assistant increases the braking force independently of the pedal force, until the maximum vehicle deceleration is achieved. This allows the shortest possible braking distance to be achieved, even if there is insufficient pedal force by the driver. |
| Electronic Differential Lock Control (EDLC) | Reproduces the function of a differential lock: if a wheel is tending to spin, it is braked incrementally so that propulsion can continue to be achieved via the other wheel of the driven axle. |
| Vehicle Stability Control (VSC) | If the vehicle starts to understeer or oversteer, it is stabilized by means of selective brake interventions on a wheel-by-wheel basis. |
| Traction mode | Compared to the VSC, Traction mode permits a higher slip at the drive wheels. Traction mode is also active when cornering, and allows for a sporty driving style. During critical situations, Traction mode intervenes with its corrections later. In comparison, the VSC provides optimum driving stability within the physical limits. |
| Brake Standby | Establishes moderate brake pressure in the system if the driver suddenly removes their foot from the accelerator pedal. If the driver then performs emergency braking, the braking effect takes hold faster. |
| Dry by Applying Brake | Lightly applies the brake pads at intervals dependent on the operation of the wipers in order to dry the brake discs. In the event of braking, this significantly improves the braking effect. |
| Fading Assist | Assists the driver during application of brake force if the brakes have reached a very high temperature due to excessive use and the desired deceleration can only be achieved with higher braking force. |
| Drive-off Assistant | Holds the vehicle still on inclines for approximately 2 seconds if the driver sets off by releasing the brake. This enables the driver to drive off comfortably without unintended rolling of the vehicle downhill. |
FUNCTION
Vehicle Stability Control (VSC)
The VSC includes a series of suspension control systems that maintain driving stability even under unfavorable driving situations. The VSC optimizes both the driving stability during drive off and the acceleration as well as the traction. Furthermore, it detects unstable driving conditions such as understeering and/or oversteering and helps keep the vehicle safely on course within the physical limits. Thereby, the VSC provides an efficient contribution to the ride comfort and active safety.
The VSC provides excellent driving stability and superb traction in all driving situations through active engine and brake activations. The system acts against all negative driving dynamic forces and thereby achieves maximum active safety and ride comfort within the physical limits. It enables a balanced ratio between traction and stability.
The VSC detects driving conditions such as oversteering and understeering using high-performance sensors which provide the following signals:
Wheel speeds
Yaw moment around the vertical axis
Lateral acceleration as a dimension for the curve radius
Steering angle
Brake pressure
Driving speed
The actual condition in which the vehicle is currently moving is determined from the available measured values. This actual condition is compared with the desired values that are stored in the skid control ECU. If the current actual values deviate from the desired state, the VSC becomes active and actively intervenes in the brake system or engine control, and the vehicle can thereby be stabilized through single-sided braking. The VSC thereby prevents dangerous skidding when it arises, within the physical limits possible.
Coordinated control
Driving performance has been further enhanced via optimized control systems.
The control system achieves further refinements to stability, traction, and steering characteristics.
Driving of the actuators has been optimized through the use of a hierarchical function structure in the control system.
Coordinated control has been integrated into the skid control ECU.
Through coordination of the Electric Power Steering (EPS) and VSC, the following functions provide improved driveability.
Limit range feedback (EPS)
Active roadway feedback (EPS)
Steering optimization (EPS)
Yaw moment compensation in the case of a mu-split (EPS)
Performance control such as dynamic handling brake intervention (VSC)
Differential lock active (GSD)