Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM3650E _59 Vehicle Exterior _079876 WINDOW / GLASS _0387523 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


PROCEDURE

Hide 62720A 1.INSTALL QUARTER WINDOW ASSEMBLY

HINT:
·

The vehicle can be towed away or driven without the quarter window assembly.

·

When carrying out removal/installation work and during the hardening time, the vehicle must be standing on its wheels on a level surface.

·

The quarter window assembly are bonded to the body. This bonding will increase the torsional rigidity of the vehicle. To obtain perfect bonding, comply with the installation procedure described in the following.



a.

Clean quarter window assembly and body aperture with residual adhesive bead.

Cleaner:

Cleaner R1, Cleaner R2


HINT:

Protect vehicle interior against contamination.



b.
B536803

Remove the remaining guide pins (1) and the double-sided tape (2) and clean the bonding surface.


c.

Apply new double-sided tape in the position of the removed double-sided tape (2).


d.
B539819

Remove residual adhesive bead (1) on body aperture and on the quarter window assembly shortly before the bonding with scraper.


e.

Position the scraper (2) as shown and remove the residual adhesive bead (1) up to remaining thickness.

Standard Dimension:
Area Dimension
Remaining thickness of adhesive bead 0.5 mm (0.0197 in.)



f.

Apply glass activator to the quarter window assembly (3) so that a wide line of glass activator is located next to the squeezed adhesive bead.

Glass activator:

Repair Kit, Window Glass, Cold, 1 Hour


NOTICE:
·

The glass activator is used for adhesion between glass or ceramic glass and the adhesive. Therefore, a thin, homogeneous and continuous line of glass activator must be applied. If the quarter window assembly is to be reused with a cut-back adhesive bead, glass activator is not needed.

·

The glass activator may not be applied in the field of view or the point grid. Fresh glass activator in the field of view must immediately be wiped off because hardened glass activator will leave a haze behind.

Cleaner:

Cleaner R2




HINT:
·

Protrusion of glass activator against the compressed adhesive bead: 1.0 to 2.0 mm (0.0394 to 0.0787 in.)

·

Allow the glass activator to dry for 2 minutes.




g.
B539808

Prepare the glue cartridge with the plastic nozzle.

Standard Nozzle C:

Repair Kit, Window Glass, Cold, 1 Hour


Standard Dimension:
Area Dimension
A 7.0 to 9.0 mm (0.276 to 0.354 in.)
B 14 to 16 mm (0.551 to 0.630 in.)



h.

Overview for quarter window assembly bonding.


i.
B536804

Follow the adhesive bead (1) around the circumference of the PVC coating (2).

Adhesive:

Repair Kit, Window Glass, Cold, 1 Hour


Adhesive bead:
Area Dimension
a 7.0 to 9.0 mm (0.276 to 0.354 in.)
b 14 to 16 mm (0.551 to 0.630 in.)



j.
B536805

Mount the quarter window assembly (1) on the side panel and thread in using guide pins (2).

HINT:

Secure the quarter window assembly (1) with the protective tape.



k.

Insert the clip.


l.
B536799

Mount edge protection (2) in area (3) and clip in the clip (1).


Hide 75752C 2.INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

a.
B536806

Clip front door window frame front moulding (1) into the front roof side rail weatherstrip retainer (2) in the direction of arrow.


b.

Clip in front roof side rail weatherstrip retainer with the front door window frame front moulding.