Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM3650E _59 Vehicle Exterior _080029 DOOR / HATCH _0388188 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


PROCEDURE

Hide 67002 1.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY

HINT:
·

The dimensions stated in this document apply at an object temperature of 20°C (68°F).

·

The aim of adjustment is to achieve a uniform gap.

·

Symmetry of the gaps between left and right sides of the vehicle has top priority.

·

In terms of door gaps the maximum deviation between the front and rear door gap must be 1.0 mm (0.039 in.).

·

No gap dimension are specified for components which cannot be adjusted.



·
B506395C02
0,0 0,0 false
(1) Hood Sub-assembly
(2) Front Door Panel Sub-assembly


Gap dimension hood sub-assembly to front door panel sub-assembly.

Standard Clearance:
Area Dimension
a 3.0 to 5.6 mm (0.118 to 0.220 in.)
b -0.7 to 1.7 mm (-0.028 to 0.067 in.)


·
B506396C02
0,0 0,0 false
(1) Front Side Panel
(2) Front Door Panel Sub-assembly


Gap dimension front side panel to front door panel sub-assembly.

Standard Clearance:
Area Dimension
a 3.3 to 5.3 mm (0.130 to 0.209 in.)
b -0.5 to 1.5 mm (-0.020 to 0.059 in.)


·
B506397C02
0,0 0,0 false
(1) Front Door Panel Sub-assembly
(2) Side Sill Trim Panel


Gap dimension front door panel sub-assembly to side sill trim panel.

Standard Clearance:
Area Dimension
a 2.5 to 5.1 mm (0.098 to 0.201 in.)
b -0.4 to 2.4 mm (-0.016 to 0.094 in.)


·
B506398C02
0,0 0,0 false
(1) Front Door Panel Sub-assembly
(2) Rear Side Panel


Gap dimension from front door panel sub-assembly to rear side panel.

Standard Clearance:
Area Dimension
a 2.8 to 4.8 mm (0.110 to 0.189 in.)
b -0.3 to 1.3 mm (-0.012 to 0.051 in.)



Hide 67002 2.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY

HINT:
·

Description is for left component only. Procedure on the right side is identical.

·

The gap dimensions form the basis for these repair instructions and must be observed without fail.



a.

Open front door.


b.
B452786

Loosen T40 bolts (1) until the front door can be moved.


c.

Adjust height of front door.


d.

Adjust the width of the front door.


e.
B452787

Check the gap dimensions between the front door and the adjacent body components.


f.

Gap dimensions do not correspond to the specifications.


g.

Adjust front door.


h.

Tighten the T40 bolts.

Torque:
19.0 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 69410 3.ADJUST FRONT DOOR LOCK STRIKER PLATE ASSEMBLY

HINT:
·

The gap dimensions form the basis for these repair instructions and must be observed without fail.

·

The bolts on front door lock striker plate assembly are loosened so far that the front door lock striker plate assembly can still be moved.



a.

Adjust height of the front door lock striker plate assembly. The door lock may not jolt or slip.


b.
B452796

Move front door lock striker plate assembly sideways in order to adjust the gap dimensions between front door and rear side panel.


c.

Tighten the T40 bolts (1).

Torque:
21.0 N*m (214 kgf*cm, 15 ft.*lbf)


d.
B452787

Check the gap dimensions between the front door and the adjacent body components.


e.

If necessary, adjust the front door again.