Home › Engine / Hybrid System › B58 (INTAKE / EXHAUST) › TURBOCHARGER
RM3650E _51 Engine / Hybrid System _080024 B58 INTAKE / EXHAUST _0388138 TURBOCHARGER G

B58 INTAKE / EXHAUST  TURBOCHARGER  INSPECTION  


CAUTION / NOTICE / HINT

Complaints of a lack of power are usually connected with one or more fault entries in the engine control unit (charging pressure control deviation). These fault entries must be processed using the diagnosis system.

PROCEDURE

Hide 1. BEARING DAMAGE

a.
A441162C01
0.083,0.073 0.25,0.25 0.167,0.177 10 true *a
*a Traces left by the impeller grinding against the housing.


If the compressor or turbine wheel rub against the housing (see picture below), the turbocharger sub-assembly is faulty. This damage leads not only to a drop below the charging pressure but also noises.


Hide 2. FOREIGN BODY ON THE TURBINE SIDE

a.

If a foreign body damages the turbine wheel, the efficiency of the turbocharger sub-assembly is severely limited and the required charging pressure is no longer reached. Where a foreign body causes damage on the turbine side, the adjustment vanes are usually also damaged in addition to the turbine wheel, which often causes the adjusting mechanism to jam.


b.

In the event of damage caused by a foreign body, it is imperative to establish how the foreign body penetrated the system and to remedy the cause, as otherwise the newly installed turbocharger sub-assembly may also be damaged.


c.
A441169

Normal turbine wheel without damage.


d.
A441170

Normal turbine wheel without damage.


e.
A441153

Turbine vanes damaged by foreign bodies.


Hide 3. FOREIGN BODY ON THE COMPRESSOR SIDE

a.

If a foreign body damages the impeller, the efficiency of the turbocharger sub-assembly is severely limited and the required charging pressure is no longer reached.


b.

In the event of damage caused by a foreign body, it is imperative to establish how the foreign body penetrated the system and to remedy the cause, as otherwise the newly installed turbocharger sub-assembly may also be damaged.

HINT:

Slight discoloration and shiny patches on the impeller arise normally during production and in operation, see the following image.



c.
A441165

Normal impeller without damage.


d.
A441154

Impeller damaged by foreign bodies.


e.
A441166

Impeller damaged by foreign bodies.


Hide 4. COMPRESSOR PUMPING

a.

The phenomenon referred to as compressor pumping can occur if the charging pressure becomes too high where there is low air mass flow. The air current at the compressor is severed abruptly and a pulsating current develops. This current can damage the compressor and cause disruptive noises.


b.

Charger pumping may occur due to defects that obstruct the air mass flow in the charge air guide or cause excessive charging pressure.


Hide 5. EXTERNAL CORROSION

a.

External corrosion on the turbine housing is not a cause for concern. External corrosion on the adjusting mechanism is also not a cause for concern as long as the function of the adjusting mechanism is OK. The function of the adjusting mechanism must be checked through the diagnosis system.


Hide 6. OIL CRUSTING ON THE COMPRESSOR INTAKE

a.

If the oil content in the blow-by gas is too high, heavy oil crusting may form on the compressor. In this case, the cause of the excessive oil content must be remedied.


b.
A441167

Normal oil accumulations in the diffuser of the compressor.


c.
A441171

Heavy oil crusting in the diffuser of the compressor.


Hide 7. OIL GRADE

a.
A441155C01
0.104,0.094 0.292,0.271 0.188,0.177 10 true *a
*a Oil deposits in the oil return


Oil of poor quality can break down and form deposits in the oil circuit. This can lead to insufficient lubrication of the turbocharger sub-assembly. Only BMW approved oil may be used.


Hide 8. CHARGE AIR ROUTING HAS A LEAK

a.
A441158

In the event of leakage in the charge air routing, the charging pressure and thus the power of the engine falls. Noises may also arise.


b.
A441156

Leaky charge air routing caused by a damaged hose.


Hide 9. AIR CLEANER CLOGGED/FAULTY OR SUCTION DUCT NARROWED

a.

If the air intake duct is blocked (for example the air cleaner is clogged/faulty or the air intake hose has collapsed etc.), this leads to a lack of air in the compressor. As a result, the compressor is not able to generate the charging pressure.


b.
A441172C01
0.094,0.104 0.406,0.26 0.313,0.156 10 false *a
*a Example: Faulty air cleaner with damaged fins (air cleaner contracts under load and blocks the air intake duct).


This fault almost always results in serious overspeeding of the turbocharger sub-assembly.


Hide 10. WIRING OF THE TURBOCHARGER ACTUATOR AND LINK ASSEMBLY IS FAULTY

a.

If the wiring of the turbocharger actuator and link assembly is faulty, the engine control cannot activate the turbocharger actuator and link assembly properly. This can have various effects (excessively high charging pressure, excessively low charging pressure, poor response characteristics).