Failure to comply with the warning notices and repair notes for gas generator components can cause accidental deployment and result in injury and vehicle damage!
This applies in particular to the following components.
Horn button assembly
Instrument panel passenger without door airbag assembly
Front seat airbag assembly
Front seat outer belt assembly
Curtain shield airbag assembly
Lower No. 1 instrument panel airbag assembly
Lower No. 2 instrument panel airbag assembly
Safety battery terminal
Airbag sensor
Side airbag pressure sensor
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
Work on components of the airbag system should only ever be carried out with the battery disconnected, the negative terminal post covered and the plug connection of the cable leading to the gas generator disconnected. If only the vehicle battery is disconnected, the prescribed waiting period of 60 seconds must be observed without fail.
The SRS is equipped with a back-up power source. If work is started within 60 seconds of disconnecting the cable from the negative (-) battery terminal, the SRS parts may deploy.
GENERAL PRECAUTION
When handling, transporting and storing gas generators, observe the country-specific regulations!
Checking and installation work must be carried out by professionally trained personnel only.
In the event of breaks In work, a component with a gas generator that has been removed must be secured against access by other persons.
Individual components must never be repaired. Instead, always replace them.
Do not treat airbag system components with cleaning agents or grease.
Components of the airbag system must not be exposed to temperatures in excess of 75 °C (167 °F).
Airbag system components, including electronic diagnostic components, which have been dropped from heights in excess of 0.5 m (1.64 ft.) must not be reinstalled in the vehicles.
Do not remove components of the airbag system from the original packaging until immediately before they are to be installed in the vehicle.
Before installing, subject components such as housing, connector pins, etc. of the airbag system to a visual inspection for damage and replace if necessary.
Airbag system components may only be electrically tested while they are installed and only with the diagnosis system.
Components with gas generators must not be fired while they are removed. They must be disposed of by special disposal companies or returned to the manufacturer in the packaging of the new parts.
Avoid all contact with the skin when removing a fired airbag module - wear gloves. Wash with water after contact with the skin.
PRECAUTION FOR HORN BUTTON ASSEMBLY, INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY, FRONT SEAT AIRBAG ASSEMBLY, CURTAIN SHIELD AIRBAG ASSEMBLY, LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY, LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
Danger of injury
The airbag module may only be set down with the airbag itself facing upwards. Otherwise the airbag module will be thrown upwards if the gas generator is ignited.
Do not point the ignition squib of a gas generator at other persons.
When storing an airbag, do not place anything on top of it or place it in a pile.
PRECAUTION FOR FRONT SEAT OUTER BELT ASSEMBLY (PRETENSIONER)
Do not point the ignition squib of a gas generator at other persons.
Do not touch the area around the retractor, even when a front seat outer belt assembly or rear seat outer belt assembly is temporarily removed during service.
If the pretensioner unexpectedly deploys and the front seat outer belt assembly or rear seat outer belt assembly is retracted during an operation, it could cause a serious accident.
When storing a pretensioner, do not place objects on top of it or place it in a pile.
PRECAUTION FOR SAFETY BATTERY TERMINAL
Do not point the ignition squib of a gas generator at other persons.
PRECAUTION FOR AIRBAG SENSOR
If a sensor has been dropped make sure to replace it with a new one.
If a sensor has been subjected to strong impact make sure to replace it with a new one.
Individual components must never be repaired. Instead, always replace them.
WHEN SERVICING DAMEGED VEHICLE
When carrying out straightening and welding work with an electric welder:
Disconnect battery.
Cover negative terminal (post).
PRECAUTION FOR SIDE AIRBAG PRESSURE SENSOR
Do not treat airbag system components with cleaning agents or grease.
Do not make any modifications to the front door that may change the inner pressure of the front door.
Individual components must never be repaired. Instead, always replace them.