Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated by the steering pad switch.
If there is a short in the circuit, the same condition as that when the switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated by the steering pad switch, and also the radio receiver assembly itself does not function.

WIRING DIAGRAM


E120417E01


INSPECTION PROCEDURE

1.INSPECT RADIO RECEIVER ASSEMBLY
I101938E02
  1. Disconnect the R3 radio receiver assembly connector.

  1. Measure the resistance.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    SW1 (R3-7) - SWG (R3-6)
    No switch is pushed
    Approx. 100 kΩ
    SW1 (R3-7) - SWG (R3-6)
    SEEK+ switch is pushed
    Approx. 0 Ω
    SW1 (R3-7) - SWG (R3-6)
    SEEK- switch is pushed
    Approx. 0.3 kΩ
    SW1 (R3-7) - SWG (R3-6)
    VOL+ switch is pushed
    Approx. 1 kΩ
    SW1 (R3-7) - SWG (R3-6)
    VOL- switch is pushed
    Approx. 3.1 kΩ
    SW2 (R3-8) - SWG (R3-6)
    No switch is pushed
    Approx. 100 kΩ
    SW2 (R3-8) - SWG (R3-6)
    MODE switch is pushed
    Approx. 0 Ω



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT STEERING PAD SWITCH LH (AU1, AU2, EAU)

E120418E01

  1. Disconnect the steering pad switch LH connector.

  1. Measure the resistance.

    Standard:

    Tester Connection
    Condition
    Specified Condition
    AU1 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU1 - EAU
    SEEK+ switch is pushed
    Approx. 0 Ω
    AU1 - EAU
    SEEK- switch is pushed
    Approx. 0.3 kΩ
    AU1 - EAU
    VOL+ switch is pushed
    Approx. 1 kΩ
    AU1 - EAU
    VOL- switch is pushed
    Approx. 3.1 kΩ
    AU2 - EAU
    No switch is pushed
    Approx. 100 kΩ
    AU2 - EAU
    MODE switch is pushed
    Approx. 0 Ω



NG
REPLACE STEERING PAD SWITCH LH
OK


3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO RECEIVER ASSEMBLY)
I101939E01
  1. Disconnect the S8 spiral cable sub-assembly connector.

  1. Disconnect the R3 radio receiver assembly connector.

  1. Check the resistance.

    Standard:
    Tester Connection
    Specified Condition
    SW1 (R3-7) - AU1 (S8-6)
    Below 1Ω
    SW2 (R3-8) - AU2 (S8-5)
    Below 1Ω
    SWG (R3-6) - EAU (S8-4)
    Below 1Ω
    SW1 (R3-7) - Body ground
    10 kΩ or higher
    SW2 (R3-8) - Body ground
    10 kΩ or higher
    SWG (R3-6) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY