AUDIO AND VISUAL SYSTEM > DTC CHECK / CLEAR |
| DIAGNOSTIC CHECK |

Start diagnostic mode (All elements come on during SW check mode).
Turn off the audio system and turn the ignition switch to the ACC position. While pressing the preset switches 1ch and 6ch at the same time, press the DISC switch 3 times.
Reference:
Service check screen.
Press the SEEK TRACK UP switch to enter the service check screen.
In service check mode, the system check and the diagnostic memory check are performed, and the check results are displayed by component codes in ascending order (physical address).
| Terms | Description |
| Component code (Physical address) | Three-digit code (in hexadecimal) given to each device comprising AVC-LAN. Corresponding to its function, individual symbol provided. |
| Logical address | Two-digit code (in hexadecimal) given to each function and device unit in each device comprising AVC-LAN. |
| Code No. physical address | Equipment Name |
| 190 | Radio receiver assembly (Audio head unit) |
| 440 | Stereo component amplifier assembly |
Finish diagnostic mode.
Press the DISC switch for 2 seconds or more, or turn the ignition switch off.
Service check mode result display (for checking the current and the past system conditions).
Press the SEEK TRACK UP/DOWN switch to see the check result of each component.

Check the result display.
| Display | Original Language | Description | Action to be Taken |
| good | Good (normal) | No DTCs are detected in either system check mode nor diagnostic memory mode. | - |
| NCON | No connection | The system recognized the component when it was registered, but the component gives no response to the diagnostic mode ON request. | Check the power source circuit and the communication circuit of the component indicated by the component code (physical address). |
| ECHN | Exchange | One or more DTCs for Exchange are detected in either system check mode or diagnostic memory mode. | Go to detailed information mode to check the trouble area, referring to the DTC list. |
| CHEC | Check | When no DTCs are detected for Exchange, one or more DTCs for Check are detected in either system check mode or diagnostic memory mode. | Go to detailed information mode to check the trouble area, referring to the DTC list. |
| OLD | Old version | Old DTC application is identified and DTC is detected in either system check mode or diagnostic memory mode. | - |
| NRES | No response | The device gives no response to any one of system check mode ON request, system check result request or diagnostic memory request. | Check the power source circuit and the communication circuit of the component indicated by the component code (physical address). |
To perform the service check again, press the preset switch 1 ch.
Detailed information mode (when displaying the DTC for a troubled component)
With CHEC or ECHN being displayed, press the preset switch 2ch to go to detailed information mode.
Press the SEEK TRACK UP/DOWN switch to display the system check result (SYS) and diagnostic memory response (CODE).


Displayed items in detailed information mode
| Division Code for DTC display | Description | The order of detailed information displayed when the TUNE UP switch is pressed. (The order is reversed when the TUNE DOWN switch is pressed.) |
| SYS | System check result is displayed. | Logical address → DTC |
| CODE | Diagnostic memory check result is displayed. | Logical address → DTC → Sub code → Connection confirmation number → The number of times of occurrence |
Check the trouble area referring to the DTC list.
To return to the service check mode, press the preset switch 3ch.
| DTC CLEAR |
Clearing an individual DTC memory (when clearing the memory of the DTC detected in the past individually)
Press the preset switch 5ch for 2 seconds or more while ECHN is displayed in service check mode or detailed information mode.
Clearing all the DTC memories (when clearing all the memories of DTCs detected in the past)
Start diagnostic mode after repairing the trouble area.
Press the preset switch 5ch for 2 seconds or more (CLR is displayed at this time).
Press the preset switch 1ch to perform the service check again, and check that no DTCs are displayed for any component codes (physical address).
Finish diagnostic mode
Press DISC for 2 seconds or more, or turn the ignition switch off.