Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A121603E02

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltages column.
The illustration above can be used as a reference to identify the ECM terminal locations.


Symbols (Terminal No.)
Wiring Colors
Terminal Descriptions
Conditions
STD Voltages
BATT (E8-3) - E1 (E6-1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
+BM (E8-7) - E1 (E6-1)
LG - BR
Power source of throttle motor
Always
9 to 14 V
IGSW (E8-9) - E1 (E6-1)
O - BR
Ignition switch
Ignition switch ON
9 to 14 V
+B (E8-1) - E1 (E6-1)
B - BR
Power source of ECM
Ignition switch ON
9 to 14 V
+B2 (E8-2) - E1 (E6-1)
B - BR
Power source of ECM
Ignition switch ON
9 to 14 V
OC1+ (E6-17) - OC1- (E6-16)
G-Y - L-B
Camshaft timing oil control valve (OCV)
Ignition switch ON
Pulse generation
(see waveform 1)
OC2+ (E6-15) - OC2- (E6-14)
L-W - L-R
Camshaft timing oil control valve (OCV)
Ignition switch ON
Pulse generation
(see waveform 1)
MREL (E8-8) - E1 (E6-1)
G-W - BR
EFI relay
Ignition switch ON
9 to 14 V
VC (E4-23) - E2 (E4-28)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.0 V
VG (E4-30) - E2G (E4-29)
R-Y - R-W
Mass air flow meter
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
THA (E4-22) - E2 (E4-28)
R-L - BR
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
THW (E4-21) - E2 (E4-28)
Y-B - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
VTA1 (E4-20) - E2 (E4-28)
G-B - BR
Throttle position sensor (for engine control)
Ignition switch ON, Throttle valve fully closed
0.5 to 1.2 V
VTA1 (E4-20) - E2 (E4-28)
G-B - BR
Throttle position sensor (for engine control)
Ignition switch ON, Throttle valve fully open
3.2 to 4.8 V
VTA2 (E4-19) - E2 (E4-28)
G-W - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
VTA2 (E4-19) - E2 (E4-28)
G-W - BR
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
4.5 to 5.0 V
VPA (E8-18) - EPA (E8-20)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
VPA (E8-18) - EPA (E8-20)
R-Y - LG-B
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (E8-19) - EPA2 (E8-21)
GR-B - R-B
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
VPA2 (E8-19) - EPA2 (E8-21)
GR-B - R-B
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
VCPA (E8-26) - EPA (E8-20)
R - LG-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
VCP2 (E8-27) - EPA2 (E8-21)
L-W - R-B
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
HA1A (E5-2) - E04 (E5-7)
HA2A (E5-1) - E05 (E5-6)
R - W-B
B-W - W-B
A/F sensor heater
Idling
Below 3.0 V
HA1A (E5-2) - E04 (E5-7)
HA2A (E5-1) - E05 (E5-6)
R - W-B
B-W - W-B
A/F sensor heater
Ignition switch ON
9 to 14 V
A1A+ (E5-22) - E1 (E6-1)
P - BR
A/F sensor
Ignition switch ON
3.3 V*1
A2A+ (E5-23) - E1 (E6-1)
W - BR
A/F sensor
Ignition switch ON
3.3 V*1
A1A- (E5-30) - E1 (E6-1)
L - BR
A/F sensor
Ignition switch ON
2.9 V*1
A2A- (E5-31) - E1 (E6-1)
R - BR
A/F sensor
Ignition switch ON
2.9 V*1
HT1B (E4-1) - E1 (E6-1)
HT2B (E5-5) - E1 (E6-1)
G - BR
L - BR
Heated oxygen sensor heater
Idling
Below 3.0 V
HT1B (E4-1) - E1 (E6-1)
HT2B (E5-5) - E1 (E6-1)
G - BR
L - BR
Heated oxygen sensor heater
Ignition switch ON
9 to 14 V
OX1B (E4-18) - E2 (E4-28)
OX2B (E5-33) - E2 (E4-28)
W - BR
B - BR
Heated oxygen sensor
Maintain engine speed at 2,500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 2)
#10 (E6-2) - E01 (E4-7)
#20 (E6-3) - E01 (E4-7)
#30 (E6-4) - E01 (E4-7)
#40 (E6-5) - E01 (E4-7)
#50 (E6-6) - E01 (E4-7)
#60 (E6-7) - E01 (E4-7)
R-L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
L - W-B
Injector
Ignition switch ON
9 to 14 V
#10 (E6-2) - E01 (E4-7)
#20 (E6-3) - E01 (E4-7)
#30 (E6-4) - E01 (E4-7)
#40 (E6-5) - E01 (E4-7)
#50 (E6-6) - E01 (E4-7)
#60 (E6-7) - E01 (E4-7)
R-L - W-B
B - W-B
R - W-B
G - W-B
Y - W-B
L - W-B
Injector
Idling
Pulse generation
(see waveform 3)
KNK1 (E5-29) - EKNK (E5-28)
B - W
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(see waveform 4)
KNK2 (E5-21) - EKN2 (E5-20)
G - R
Knock sensor
Maintain engine speed at 4,000 rpm after warming up
Pulse generation
(see waveform 4)
VV1+ (E6-19) - VV1- (E6-29)
R - G
Variable valve timing (VVT) sensor
Idling
Pulse generation
(see waveform 5)
VV2+ (E6-18) - VV2- (E6-28)
Y - L
Variable valve timing (VVT) sensor
Idling
Pulse generation
(see waveform 5)
NE+ (E6-21) - NE- (E6-20)
B - W
Crankshaft position sensor
Idling
Pulse generation
(see waveform 5)
IGT1 (E4-8) - E1 (E6-1)
IGT2 (E4-9) - E1 (E6-1)
IGT3 (E4-10) - E1 (E6-1)
IGT4 (E4-11) - E1 (E6-1)
IGT5 (E4-12) - E1 (E6-1)
IGT6 (E4-13) - E1 (E6-1)
P - BR
P-L - BR
LG - BR
LG-B - BR
GR - BR
G - BR
Ignition coil with igniter (ignition signal)
Idling
Pulse generation
(see waveform 6)
IGF1 (E4-24) - E1 (E6-1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Ignition switch ON
4.5 to 5.0 V
IGF1 (E4-24) - E1 (E6-1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Idling
Pulse generation
(see waveform 6)
PRG (E4-34) - E1 (E6-1)
Y - BR
Purge VSV
Ignition switch ON
9 to 14 V
PRG (E4-34) - E1 (E6-1)
Y - BR
Purge VSV
Idling
Pulse generation
(see waveform 7)
SPD (E7-8) - E1 (E6-1)
V-W - BR
Speed signal from combination meter
Ignition switch ON, Rotate driving wheel slowly
Pulse generation
(see waveform 8)
STA (E6-11) - E1 (E6-1)
B-Y - BR
Starter signal
Cranking
9 to 14 V
STP (E8-15) - E1 (E6-1)
L - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
STP (E8-15) - E1 (E6-1)
L - BR
Stop light switch
Brake pedal released
Below 1.5 V
ST1- (E8-16) - E1 (E6-1)
V-W - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
ST1- (E8-16) - E1 (E6-1)
V-W - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, Brake pedal released
7.5 to 14 V
NSW (E5-8) - E1 (E6-1)
V - BR
Park/Neutral position switch
Ignition switch ON, Shift lever position in P or N
Below 3.0 V
NSW (E5-8) - E1 (E6-1)
V - BR
Park/Neutral position switch
Ignition switch ON, Shift lever position other than P and N
9 to 14 V
M+ (E4-5) - ME01 (E5-3)
P - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 9)
M- (E4-4) - ME01 (E5-3)
L - W-B
Throttle motor
Idling with warm engine
Pulse generation
(see waveform 10)
FC (E8-10) - E1 (E6-1)
L-B - BR
Fuel pump control
Ignition switch ON
9 to 14 V
FPR (E6-30) - E1 (E6-1)
Y-R - BR
Fuel pump control
Ignition switch ON
9 to 14 V
W (E7-30) - E1 (E6-1)
BR - BR
MIL
Ignition switch ON
Below 3.0 V
W (E7-30) - E1 (E6-1)
BR - BR
MIL
Idling
9 to 14 V
ELS (E7-13) - E1 (E6-1)
G - BR
Electric load
Defogger switch OFF
0 to 1.5 V
ELS (E7-13) - E1 (E6-1)
G - BR
Electric load
Defogger switch ON
7.5 to 14 V
ELS2 (E7-12) - E1 (E6-1)
B-W - BR
Electric load
Taillight switch OFF
0 to 1.5 V
ELS2 (E7-12) - E1 (E6-1)
B-W - BR
Electric load
Taillight switch ON
7.5 to 14 V
TC (E8-23) - E1 (E6-1)
P-B - BR
Terminal TC of DLC 3
Ignition switch ON
9 to 14 V
TACH (E7-1) - E1 (E6-1)
B-W - BR
Engine speed
Idling
Pulse generation
(see waveform 11)
ACIS (E4-33) - E1 (E6-1)
W-L - BR
VSV for ACIS
Ignition switch ON
9 to 14 V
PSW (E6-10) - E1 (E6-1)
G-W - BR
P/S pressure switch
Ignition switch ON
9 to 14 V
VPMP (E8-5) - E1 (E6-1)
V-W - BR
Vent valve
(built into canister pump module)
Ignition switch ON
9 to 14 V
MPMP (E8-6) - E1 (E6-1)
G - BR
Leak detection pump
(built into canister pump module)
Leak detection pump OFF
0 to 3 V
MPMP (E8-6) - E1 (E6-1)
G - BR
Leak detection pump
(built into canister pump module)
Leak detection pump ON
9 to 14 V
PPMP (E8-22) - E2 (E4-28)
GR - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
F/PS (E7-32) - E1 (E6-1)
R - BR
Airbag sensor assembly
Idling with warm engine
Pulse generation
(see waveform 12)
CANH (E7-33) - E1 (E6-1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 13)
CANL (E7-34) - E1 (E6-1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 14)
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E07
Camshaft timing oil control valve (OCV) 
ECM Terminal Names
Between OC1+ and OC1- or OC2+ and OC2-
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2
A088863E02
Heated oxygen sensor 
ECM Terminal Names
Between OX1B and E2 or OX2B and E2
Tester Ranges
0.2 V/DIV, 200 msec./DIV
Conditions
Engine speed maintained at 2,500 rpm for 2 minutes after warming up sensor

HINT:
In the DATA LIST, item O2S B1S2 or O2S B2S2 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 3
G035622E03
Fuel injector 
ECM Terminal Names
Between #10 (to 60) and E01
Tester Ranges
30 V/DIV, 20 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4
A085286E23
Knock sensor 
ECM Terminal Names
Between KNK1 and EKNK or KNK2 and EKN2
Tester Ranges
0.01 to 10 V/DIV, 0.01 to 10 msec./DIV
Conditions
Engine speed maintained at 4,000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine rpm increases.
  2. The waveforms and amplitudes displayed on the tester differ slightly depending on the vehicle.


WAVEFORM 5
G035795E14
  1. VVT sensor

  2. Crankshaft position sensor
    ECM Terminal Names
    (a) Between NE+ and NE-
    (b) Between VV1+ and VV1- or VV2+ and VV2-
    Tester Ranges
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 6
G035664E03
  1. Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)
    ECM Terminal Names
    (a) Between IGT (1 to 6) and E1
    (b) Between IGF1 and E1
    Tester Ranges 2
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 7
A116415E02
Purge VSV 
ECM Terminal Names
Between PRG and E01
Tester Ranges
10 V/DIV, 50 msec./DIV
Conditions
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 8
A093224E02
Vehicle speed signal 
ECM Terminal Names
Between SPD and E1
Tester Ranges
2 V/DIV, 20 msec./DIV
Conditions
Driving at 12 mph (20 km/h)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 9
A093274E02
Throttle actuator positive terminal 
ECM Terminal Names
Between M+ and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 10
A093275E02
Throttle actuator negative terminal 
ECM Terminal Names
Between M- and ME01
Tester Ranges
5 V/DIV, 1 msec./DIV
Conditions
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A093225E03
Engine speed signal 
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV, 10 msec./DIV
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 12
A093227E03
Airbag sensor assembly 
ECM Terminal Names
Between F/PS and E1
Tester Ranges
5 V/DIV, 500 msec./DIV
Conditions
Idling with warm engine

WAVEFORM 13
A086154E01
CAN communication signal 
ECM Terminal Names
Between CANH and E1
Tester Ranges
1 V/DIV, 10μsec./DIV
Conditions
Stop engine and ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.


WAVEFORM 14
A086155E06
CAN communication signal 
ECM Terminal Names
Between CANL and E1
Tester Ranges
1 V/DIV, 10μsec./DIV
Conditions
Stop engine and ignition switch ON

HINT:
The wavelength varies depending on the CAN communication signal.