Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2102    Throttle Actuator Control Motor Circuit Low

DTC    P2103    Throttle Actuator Control Motor Circuit High

for Preparation Click here


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle body. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.

DTC No.
DTC Detection Conditions
Trouble Areas
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
  1. (a) Throttle actuator duty ratio 80 % or more
  2. (b) Throttle actuator current 0.5 A or less
  1. Open in throttle actuator circuit
  1. Throttle actuator
  1. ECM
P2103
Either of following conditions met:
  1. Hybrid IC diagnosis signal fail
  2. Hybrid IC current limiter port fail
  1. Short in throttle actuator circuit
  1. Throttle actuator
  1. Throttle valve
  1. Throttle body assembly
  1. ECM


MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and sets a DTC.
Example:
When the electrical current is more than 10 A, or less than 0.5 A and the throttle actuator duty ratio exceeds 80 %, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and sets a DTC.
If the malfunction is not repaired successfully, a DTC is set when the engine is quickly revved to a high rpm several times after the engine has idled for 5 seconds after engine start.

FAIL-SAFE

When either of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned to OFF.

MONITOR STRATEGY


Related DTCs
P2102: Throttle actuator current (low current)
P2103: Throttle actuator current (high current)
Required Sensors/Components (Main)
Throttle actuator (throttle body)
Required Sensors/Components (Related)
None
Frequency of Operation
Continuous
Duration
P2102: 2 seconds
P2103: 0.6 seconds or conditions met 25 times
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

P2102: 
Duty ratio to open throttle actuator
80 % or more
Throttle actuator power supply
8 V or more

P2103: 
Throttle actuator power supply
8 V or more

TYPICAL MALFUNCTION THRESHOLDS


P2102: 
Throttle actuator current
Less than 0.5 A

P2103: 
Either of following conditions met:
A or B
A. Hybrid IC diagnosis signal
Fail
B. Hybrid IC current limiter port
Fail

WIRING DIAGRAM


A121757E01


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
  1. The throttle actuator current (THROTTLE MOT) and the throttle actuator duty ratio (THROTTLE OPN / THROTTLE CLS) can be read using an intelligent tester. However the ECM shuts off the throttle actuator current when the ETCS malfunctions.

1.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE ACTUATOR RESISTANCE)
A059778E20
  1. Disconnect the T1 throttle body connector.

  1. Measure the resistance between the terminals of the throttle body.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    M+ (2) - M- (1)
    0.3 to 100 Ω at 20°C (68°F)

  1. Reconnect the throttle body connector.



NG
REPLACE THROTTLE BODY
OK


2.CHECK HARNESS AND CONNECTOR (THROTTLE ACTUATOR - ECM)
A115619E01
  1. Disconnect the T1 throttle body connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    M+ (T1-2) - M+ (E4-5)
    Below 1 Ω
    M- (T1-1) - M- (E4-4)
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    M+ (T1-2) or M+ (E4-5) - Body ground
    10 kΩ or higher
    M- (T1-1) or M- (E4-4) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT THROTTLE BODY
  1. Check for foreign objects between the throttle valve and the housing.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY
OK


4.INSPECT THROTTLE VALVE
  1. Check if the throttle valve opens and closes smoothly.



NG
REPLACE THROTTLE BODY
OK

REPLACE ECM