Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends signals to the ECM depending on the cruise control main switch condition.
The battery supplies the positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECM receives the voltage as the signal according to the switch condition.

WIRING DIAGRAM


B125022E02


INSPECTION PROCEDURE

1.INSPECT CRUISE CONTROL MAIN SWITCH


    I045145E01
  1. Turn the ignition switch off.

  1. Disconnect the cruise control main switch connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 3
+ / RES
235 to 245 Ω
1 - 3
- / SET
617 to 643 Ω
1 - 3
CANCEL
1,509 to 1,571 Ω
1 - 3
Main Switch OFF
10 kΩ or higher
1 - 3
Main Switch ON
Below 1 Ω

  1. Reconnect the cruise control main switch connector.



NG
REPLACE CRUISE CONTROL MAIN SWITCH
OK


2.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE SUB-ASSEMBLY)


  1. Disconnect the spiral cable side connector.


    B125026E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 1 (ECC) main switch side - Terminal 3 (ECC) spiral cable side
    Always
    Below 1 Ω
    Terminal 3 (ECC) main switch side - Terminal 4 (ECC) spiral cable side
    Always
    Below 1 Ω

  1. Reconnect the spiral cable side connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
I044973E01
  1. Disconnect the spiral cable connector on the ECM side.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Terminal 4 (ECC) main switch side - CCS (S8-1)
    Always
    Below 1 Ω
    Terminal 3 (ECC) main switch side - ECC (S8-2)
    Always
    Below 1 Ω



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    I038526E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECC (S8-2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)


    I101321E01
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (1GR-FE):
    Tester Connection
    Condition
    Specified Condition
    CCS (E7-2) - CCS (S8-1)
    Always
    Below 1 Ω
    CCS (E7-2) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (2TR-FE):
    Tester Connection
    Condition
    Specified Condition
    CCS (E7-31) - CCS (S8-1)
    Always
    Below 1 Ω
    CCS (E7-31) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE