Home › ENGINE ยท 2TR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


G037896E02
  1. Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.



    G037897E01
  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.

  1. Apply a light coat of gasoline or spindle oil to the O-ring again, then install the fuel injector into the fuel delivery pipe by turning it right and left.

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate, replace the O-ring.



2. INSTALL FUEL DELIVERY PIPE W/ INJECTOR


G037898E01
  1. Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each spacer.

  1. Install the 4 spacers onto the cylinder head.

  1. Install 4 new injector vibration insulators onto the cylinder head.

  1. Install the 2 delivery pipe No. 1 spacers onto the cylinder head.



    G037716E01
  1. Install the fuel delivery pipe together with the 4 fuel injectors, then provisionally tighten the fuel delivery pipe with the 2 bolts.

    NOTICE:
    Do not drop the fuel injectors when installing the fuel delivery pipe.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate, replace the O-ring.

  1. Retighten the 2 bolts to the specified torque.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    G037715E01
  1. Install the harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the wire harness clamp.

  1. Connect the compressor magnetic clutch connector. (with AIR CONDITIONING)



    G037714E01
  1. Connect the engine wire harness clamp.

  1. Connect the VSV connector.

  1. Connect the 4 injector connectors.



3. INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY


G037906E01
  1. Apply a light coat of gasoline or spindle oil to the O-ring.



    G037905E01
  1. Install the fuel pressure pulsation damper with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



4. CONNECT FUEL HOSE


G037903E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



5. CONNECT FUEL HOSE NO.2


G037904E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



6. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY


    G037700E01
  1. Install a new gasket onto the intake manifold.



    G037699E01
  1. Install the throttle with motor body with the 2 bolts and 2 nuts.

    Torque:
    9 N*m{ 92 kgf*cm , 80 in.*lbf }



    G037698E01
  1. Connect the water by-pass hose.

  1. Connect the water by-pass hose No. 2.

  1. Connect the throttle motor connector.



7. INSTALL INTAKE AIR CONNECTOR


    G037697E01
  1. Install the intake air connector with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts.

    Torque:
    5 N*m{ 51 kgf*cm , 44 in.*lbf }



    G037696E01
  1. Connect the vacuum hose.



    G037695E01
  1. Connect the ventilation hose No. 2.



    G037694E01
  1. Connect the vacuum hose.

  1. Engage the wire harness clamp.

  1. Connect the pressure sensor connector.



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
3.9 N*m{ 40 kgf*cm , 35 in.*lbf }



9. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.



11. CHECK FOR FUEL LEAKAGE


G035612E02
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD / ON.

  1. Check that there are no leakage in the fuel system.



12. INSTALL ENGINE UNDER COVER SUB-ASSEMBLY NO.1