Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B065593E08

  1. Disconnect the T9 amplifier connector.

  2. Measure the resistance of the wire harness side connector.

    Standard resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (T9-7) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T9 amplifier connector.

  4. Measure the resistance and voltage of the connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (T9-1) - AGND(T9-7)
    GR-B - L
    Power source
    No key in ignition key cylinder
    0 V
    VC5 (T9-1) - AGND(T9-7)
    GR-B - L
    Power source
    Key inserted
    4.6 to 5.4 V
    CODE (T9-4) - AGND (T9-7)
    P-G - L
    Demodulated signal of key code data
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    TXCT (T9-5) - AGND (T9-7)
    LG-R - L
    Key code output signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    AGND (T9-7) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the amplifier.



  5. Inspect using an oscilloscope.



      B051053E02
    1. Waveform 1
      Terminal
      CODE (T9-4) - AGND (T9-7)
      Tool Setting
      2 V/DIV., 20 msec/DIV.
      Condition
      No key in ignition key cylinder → Key inserted



    2. B051052E01
    3. Waveform 2
      Terminal
      TXCT (T9-5) - AGND (T9-7)
      Tool Setting
      2 V/DIV., 20 msec/DIV.
      Condition
      No key in ignition key cylinder → Key inserted


CHECK TRANSPONDER KEY ECU ASSEMBLY

B081103E01

  1. Disconnect the T10 ECU connector.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (T10-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    +B (T10-1) - GND (T10-16)
    R - W-B
    Battery
    Always
    10 to 14 V
    IG (T10-2) - GND (T10-16)
    O - W-B
    Ignition switch
    Ignition switch OFF
    0 V
    IG (T10-2) - GND (T10-16)
    O - W-B
    Ignition switch
    Ignition switch ON
    10 to 14 V
    KSW (T10-3) - AGND (T10-5)
    G-B - L
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    KSW (T10-3) - AGND (T10-5)
    G-B - L
    Unlock warning switch
    Key inserted
    Below 1Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T10 ECU connector.

  4. Measure the voltage of the connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (T10-14) - GND (T10-16)
    GR-B - W-B
    Power source
    No key in ignition key cylinder
    0 V
    VC5 (T10-14) - GND (T10-16)
    GR-B - W-B
    Power source
    Key inserted
    4.6 to 5.4 V
    TXCT (T10-4) - GND (T10-16)
    LG-R - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    CODE (T10-15) - GND (T10-16)
    P-G - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    EFIO (T10-13) - GND (T10-16)
    L-W - W-B
    ECM output signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 3)
    EFII (T10-12) - GND (T10-16)
    LG-B - W-B
    ECM input signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 4)
    If the result is not as specified, there may be a malfunction on the ECU.



  5. Inspect using an oscilloscope.



      B051052E02
    1. Waveform 1
      Terminal
      TXCT (T10-4) - GND (T10-16)
      Tool Setting
      2.5 V/DIV., 20 msec/DIV.
      Condition
      No key in ignition key cylinder → Key inserted



    2. B051053E04
    3. Waveform 2 (Reference)
      Terminal
      CODE (T10-15) - GND (T10-16)
      Tool Setting
      2.5 V/DIV., 20 msec/DIV.
      Condition
      No key in ignition key cylinder → Key inserted



    4. B051050E01
    5. Waveform 3
      Terminal
      EFIO (T10-13) - GND (T10-16)
      Tool Setting
      12 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON



    6. B051051E01
    7. Waveform 4
      Terminal
      EFII (T10-12) - GND (T10-16)
      Tool Setting
      10 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON


CHECK ECM (2TR-FE)

A066714E18

  1. Disconnect the E7 and E8 ECM connectors.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (E7-16) - EOM (E8-29)
    L-W - W-B
    Transponder key ECU input signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 1)
    IMO (E7-15) - EOM (E8-29)
    LG-B - W-B
    Transponder key ECU output signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 2)
    EOM (E8-29) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, the ECM may have a malfunction.



  3. Inspect using an oscilloscope.



      B051050E01
    1. Waveform 1
      Terminal
      IMI (E7-16) - EOM (E8-29)
      Tool Setting
      12 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON



    2. B051051E01
    3. Waveform 2
      Terminal
      IMO (E7-15) - EOM (E8-29)
      Tool Setting
      10 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON


CHECK ECM (1GR-FE)

G035613E13

  1. Disconnect the E7 ECM connectors.

  2. Measure the resistance and voltage of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (E7-16) - EOM (E7-35)
    L-W - W-B
    Transponder key ECU input signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 1)
    IMO (E7-15) - EOM (E7-35)
    LG-B - W-B
    Transponder key ECU output signal
    Ignition switch OFF → ON
    Pulse generation
    (see waveform 2)
    EOM (E7-35) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, the ECM may have a malfunction.



  3. Inspect using an oscilloscope.



      B051050E01
    1. Waveform 1
      Terminal
      IMI (E7-16) - EOM (E7-35)
      Tool Setting
      12 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON



    2. B051051E01
    3. Waveform 2
      Terminal
      IMO (E7-15) - EOM (E7-35)
      Tool Setting
      10 V/DIV., 100 msec/DIV.
      Condition
      Ignition switch OFF → ON