Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0125    Insufficient Coolant Temperature for Closed Loop Fuel Control

for Preparation Click here


DESCRIPTION

Refer to DTC P0115 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0125
Engine coolant temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period varies with engine start ECT) (2 trip detection logic)
  1. Cooling system
  2. Engine coolant temperature sensor
  3. Thermostat

MONITOR DESCRIPTION

The resistance of the ECT sensor varies in proportion to the actual ECT. The ECM supplies a constant voltage to the sensor and monitors the signal output voltage of the sensor. The signal voltage output varies according to the changing resistance of the sensor. After the engine is started, the ECT is monitored through this signal. If the ECT sensor indicates that the engine is not yet warm enough for closed-loop fuel control, despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and sets the DTC.
Example:
The ECT is 0°C (32°F) at engine start. After 5 minutes running time, the ECT sensor still indicates that the engine is not warm enough to begin closed-loop fuel (air-fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0125: Insufficient engine coolant temperature for closed-loop fuel control
Required Sensors/Components (Main)
Thermostat, cooling system
Required Sensors/Components (Related)
Engine coolant temperature sensor and mass air flow meter
Frequency of Operation
Continuous
Duration
56 seconds: Closed-loop enable temperature - 8.34°C (15°F) or more
98 seconds: Closed-loop enable temperature - 19.45 to - 8.34°C (35 to 15°F)
1200 seconds: Less than closed-loop enable temperature - 19.45°C (35°F)
MIL Operation
2 driving cycles
Sequence of Operation
P0100 - P0103 (MAF sensor)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
P0100 - P0103 (MAF meter)
P0110 - P0113 (IAT sensor)
P0115 - P0118 (ECT sensor)

Case 1 
Engine coolant temperature or intake air temperature at engine start
"Closed-loop enabling temperature - 8.34°C (15°F)" or more
Engine
Running
Fuel cut
OFF

Case 2 
Engine coolant temperature or intake air temperature at engine start
Between "Closed-loop enabling temperature - 19.45°C (35°F)" and "Closed-loop enabling temperature - 8.34°C (15°F)"
Engine
Running
Fuel cut
OFF

Case 3 
Engine coolant temperature or intake air temperature at engine start
Lower than "Closed-loop enabling temperature - 19.45°C (35°F)"
Engine
Running
Fuel cut
OFF
Idle
OFF

TYPICAL MALFUNCTION THRESHOLDS


Engine coolant temperature
Lower than closed-loop enabling temperature

WIRING DIAGRAM

Refer to DTC P0115 .

INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0116, P0117 or P0118 are set simultaneously with DTC P0125, the Engine Coolant Temperature (ECT) sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0125
    A
    P0125 and other DTCs
    B

    HINT:
    If any DTCs other than P0125 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT W/THERMOSTAT WATER INLET SUB-ASSEMBLY (THERMOSTAT)
  1. Remove the w/ thermostat water inlet sub-assembly (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard:
    80° to 84°C (176° to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the w/ thermostat water inlet sub-assembly (Click here).



NG
REPLACE W/THERMOSTAT WATER INLET SUB-ASSEMBLY
OK


3.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR