Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Conditions
Trouble Areas
P0335
  1. No CKP sensor signal to ECM while cranking (1 trip detection logic)
  1. No CKP sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in CKP sensor circuit
  2. CKP sensor
  3. Sensor plate (CKP sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic)
  1. (a) Engine speed 1,000 rpm or more
  2. (b) Starter signal OFF
  3. (c) 3 seconds or more have lapsed since starter signal switched from ON to OFF

  1. G035795E10
  2. Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
      Items
      Contents
      Terminals
      VV1+ - VV1-
      VV2+ - VV2-
      NE+ - NE-
      Equipment Settings
      5 V/DIV, 20msec./DIV.
      Conditions
      Cranking or idling


MONITOR DESCRIPTION

If there is no signal from the CKP sensor despite the engine revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is set 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check during cranking
P0335: Crankshaft position sensor range check during engine running
Required Sensors/Components (Main)
Crankshaft Position (CKP) sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
Conditions met for 3 times: CKP sensor range check during cranking
0.016 seconds: CKP sensor range check during engine running
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
None

Case 1: 
Time after starter OFF to ON
0.3 seconds or more
Number of camshaft position sensor signal pulse
6 times
Battery voltage
7 V or more
Ignition switch
ON

Case 2: 
Starter
OFF
Engine RPM
600 rpm or more
Time after starter from ON to OFF
3 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Case 1: 
Number of CKP sensor signal pulse
132 or less, or 174 or more

Case 2: 
Engine speed signal
No signal

COMPONENT OPERATING RANGE


CKP sensor
  1. CKP sensor output voltage fluctuates while crankshaft revolving
  2. 34 CKP sensor signals per crankshaft revolution

WIRING DIAGRAM


A115939E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical systems.
  2. Check the engine speed. The engine speed can be checked by using an intelligent tester. To check, follow the operation below:
    1. Connect an intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the tester ON
    4. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / ENGINE SPD.
    1. The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor voltage output is insufficient.
  3. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
A078431E04
  1. Disconnect the C5 Crankshaft Position (CKP) sensor connector.

  1. Measure the resistance between terminals 1 and 2.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    1,630 Ω to 2,740 Ω at cold
    1 - 2
    2,065 Ω to 3,225 Ω at hot

    HINT:
    Terms cold and hot refer to the temperature of the coils. Cold means approximately -10° to 50°C (14° to 122°F). Hot means approximately 50° to 100°C (122° to 212°F).

  1. Reconnect the CKP sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A116290E02
  1. Disconnect the C5 CKP sensor connector.

  1. Disconnect the E6 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    NE+ (C5-1) - NE+ (E6-21)
    Below 1 Ω
    NE- (C5-2) - NE- (E6-20)

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    NE+ (C5-1) or NE+ (E6-21) - Body ground
    10 kΩ or higher
    NE- (C5-2) or NE- (E6-20) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the CKP sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E32
  1. Check the CKP sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR
OK


4.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE(CRANKSHAFT))
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK

REPLACE ECM