Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A121768E01


INSPECTION PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
A018294E37
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (E8-1) - E1 (E4-3)
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A065743E26
  1. Disconnect the negative battery cable.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    E1 (E4-3) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.

  1. Reconnect the negative battery cable.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGSW VOLTAGE)
A018294E38
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGSW (E8-9) - E1 (E4-3)
    9 to 14 V



OK
Go to step 6
NG


4.CHECK FUSE (AM2 AND IGN)
A115876E01
  1. Check the AM2 fuse.

    1. Remove the AM2 fuse from the engine room R/B.

    2. Check the AM2 fuse resistance.

      Standard Resistance:
      Below 1 Ω

    3. Reinstall the AM2 fuse.

  1. Check the IGN fuse.

    1. Remove the IGN fuse from the driver side J/B.

    2. Check the IGN fuse resistance.

      Standard Resistance:
      Below 1 Ω

    3. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE
OK


5.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
G037118E01
  1. Disconnect the I7 ignition switch connector.

  1. Check the resistance.

    Standard Resistance:
    Ignition Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2-4
    Below 1 Ω
    ON
    1-4, 1-6, 2-4, 3-4, 5-6
    Below 1 Ω
    START
    1-4, 3-4, 5-6, 5-7
    Below 1 Ω

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK

CHECK AND REPAIR HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM) 

6.INSPECT ECM (MREL VOLTAGE)
A018294E39
  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    MREL (E8-8) - E1 (E4-3)
    9 to 14 V



NG
REPLACE ECM
OK


7.CHECK FUSE (EFI)
G035646E02
  1. Remove the EFI fuse from the engine room R/B.

  1. Check the EFI fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE
OK


8.INSPECT EFI RELAY
A054773E02
  1. Remove the EFI relay from the engine room R/B.

  1. Check the EFI relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the EFI relay.



NG
REPLACE EFI RELAY
OK


9.CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM, EFI RELAY - BODY GROUND)
A115877E01
  1. Check the harness and connector between the EFI relay and ECM.

    1. Remove the EFI relay from the engine room R/B.

    2. Disconnect the E8 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      Engine room R/B (EFI relay terminal 1) - MREL (E8-8)
      Below 1 Ω
      Engine room R/B (EFI relay terminal 3) - +B (E8-1)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      Engine room R/B (EFI relay terminal 1) or MREL (E8-8) - Body ground
      10 kΩ or higher
      Engine room R/B (EFI relay terminal 3) or +B (E8-1) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reinstall the EFI relay.

  1. Check the harness and connector between the EFI relay and body ground.

    1. Remove the EFI relay from the engine room R/B.

    2. Check the resistance.

      Standard Resistance (Check for open)::
      Tester Connections
      Specified Conditions
      Engine room R/B (EFI relay terminal 2) - Body ground
      Below 1 Ω

    3. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPLACE HARNESS AND CONNECTOR (TERMINAL 5 OF EFI RELAY - BATTERY POSITIVE TERMINAL)