Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0110    Intake Air Temperature Circuit

DTC    P0112    Intake Air Temperature Circuit Low Input

DTC    P0113    Intake Air Temperature Circuit High Input

for Preparation Click here


DESCRIPTION


  1. A067628E03
    The Intake Air Temperature (IAT) sensor, built into the Mass Air Flow (MAF) meter, monitors the intake air temperature. The IAT sensor has a thermistor that varies its resistance depending on the intake air temperature. When the intake air temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are reflected as voltage changes to the ECM terminal (see Fig. 1).
    The IAT sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the IAT sensor from terminal THA via resistor R.
    Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.

    HINT:
    When any of DTCs P0110,P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
Proceed To
DTC Detection Conditions
Trouble Areas
P0110
Step 1
Open or short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open or short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0112
Step 4
Short in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM
P0113
Step 2
Open in IAT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in IAT sensor circuit
  2. IAT sensor (built into MAF meter)
  3. ECM

HINT:
When any of these DTCs are set, check the Intake Air Temperature (IAT) by selecting the following menu items on an intelligent tester: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.


Temperature Displayed
Malfunctions
-40°C (-40°F)
Open circuit
140°C (284°F)
Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the IAT sensor and sets a DTC.
Example:
If the sensor voltage output is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the IAT sensor circuit, and sets DTC P0113. Conversely, if the voltage output is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P0112.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0110: IAT sensor range check (Fluctuating)
P0112: IAT sensor range check (Low voltage)
P0113: IAT sensor range check (High voltage)
Required Sensors/Components (Main)
IAT sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever these DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0110: 
IAT sensor voltage
Less than 0.18 V, or more than 4.91 V

P0112: 
IAT sensor voltage [intake air temperature]
Less than 0.18 V [more than 140°C (284°F)]

P0113: 
IAT sensor voltage [intake air temperature]
More than 4.91 V [less than -40°C (-40°F)]

COMPONENT OPERATING RANGE


IAT sensor voltage [intake air temperature]
0.18 V to 4.91 V [-40 to 140°C (-40 to 284°F)]

WIRING DIAGRAM


A121738E01


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ DATA LIST (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.

  1. Read the values displayed on the tester.

    Standard:
    Same value as actual IAT.

    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    Same as actual IAT
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2.READ DATA LIST (CHECK FOR OPEN IN WIRE HARNESS)
A103707E10
  1. Disconnect the M1 MAF meter connector.

  1. Connect terminals THA and E2 of the MAF meter wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F)

  1. Reconnect the MAF meter connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER
NG


3.READ DATA LIST (CHECK FOR OPEN IN ECM)
A123979E01
  1. Disconnect the M1 MAF meter connector.

  1. Connect terminals THA and E2 of the ECM connector.

    HINT:
    Before checking, do a visual and contact pressure check for the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.

  1. Read the value displayed on the tester.

    Standard:
    140°C (284°F)

  1. Reconnect the MAF meter connector.



NG
CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

4.READ DATA LIST (CHECK FOR SHORT IN WIRE HARNESS)
A084869E36
  1. Disconnect the M1 MAF meter connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the MAF meter connector.



OK
REPLACE MASS AIR FLOW METER
NG


5.READ DATA LIST (CHECK FOR SHORT IN ECM)
A124075E02
  1. Disconnect the E4 and E5 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / INTAKE AIR.

  1. Read the value displayed on the tester.

    Standard:
    -40°C (-40°F)

  1. Reconnect the ECM connectors.



NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR