Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0010    Camshaft Position "A" Actuator Circuit (Bank 1)

for Preparation Click here

HINT:
This DTC relates to the Oil Control Valve (OCV).


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, OCV and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature.
The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A117755E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0010
Open or short in OCV circuit(1 trip detection logic)
  1. Open or short in OCV circuit
  2. OCV
  3. ECM

MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake camshaft. The VVT system includes the ECM, the OCV and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
After the ECM sends the target duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an actual duty-cycle. The ECM determines the existence of a malfunction and sets the DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

MONITOR STRATEGY


Related DTCs
P0010: VVT OCV range check
Required Sensors/Components (Main)
VVT OCV
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
All of following conditions met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch off to on
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions met
-
A. All of following conditions met
-
Battery voltage
11 to 13 V
Target duty ratio
Less than 70 %
Output signal duty ratio
100 %
B. All of following conditions met
-
Battery voltage
13 V or more
Target duty ratio
Less than 80 %
Output signal duty ratio
100 %
C. All of following conditions met
-
Current cut status
Not cut
Output signal duty ratio
3 % or less

COMPONENT OPERATING RANGE


VVT OCV duty ratio
3 to 100%

WIRING DIAGRAM


A121736E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
  1. Connect an intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Warm up the engine.

  1. On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / VVT CTRL B1.

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

    Result:
    Tester Operations
    Specified Conditions
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV SIGNAL)
A094633E32
  1. Disconnect the C2 OCV connector.

  1. While idling, check the waveform between the terminals of the OCV connector using an oscilloscope.

    Standard:
    Tester Connections
    Specified Conditions
    OCV+ (C2-1) - OCV- (C2-2)
    Correct waveform shown

  1. Reconnect the OCV connector.



OK
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
NG


3.INSPECT ECM (OCV SIGNAL)
A093256E04
  1. Inspect the ECM using an oscilloscope.

  1. While idling, check the waveform between the terminals of the ECM connector.

    Standard:
    Tester Connections
    Specified Conditions
    OC1+ (E4-13) - OC1- (E4-12)
    Correct waveform shown



NG
REPLACE ECM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR