Home › ENGINE ยท 2TR-FE › COOLING › THERMOSTAT

THERMOSTAT > INSTALLATION

for Preparation Click here



1. INSTALL THERMOSTAT


G038202E01
  1. Install a new gasket onto the thermostat.

  1. Install the thermostat with the jiggle valve upward.

    HINT:
    The jiggle valve may be set within 10° to either side of the prescribed position.



2. INSTALL WATER INLET


G038200E02
  1. Install a new gasket and the water inlet with the bolt and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



3. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



4. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.