Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P2716    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

A116546E01
The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the duty cycle of the SLT solenoid valve to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
Duty Ratio:
The duty ratio is the ratio of the period of continuity in one cycle. For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then Duty Ratio = A / (A + B) x 100 (%).

DTC No.
DTC Detection Conditions
Trouble Areas
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving. (1-trip detection logic)
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

Reference (Using an oscilloscope):
Check the waveform between terminals SLT+ and SLT- of the ECM connector.
G023426E09

Standard:
Refer to the illustration.
Item
Content
Terminal
SLT+ (E5-12) - SLT- (E5-13)
Tool setting
5 V/DIV
1 ms/DIV
Vehicle condition
Engine idle speed


MONITOR DESCRIPTION

When an open or short is detected in the linear solenoid valve (SLT) circuit, the ECM interprets this as a fault. The ECM turns on the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not present.
None
Solenoid current cut status
Not cut
Battery voltage
11 V or more
CPU command duty ratio to SLT
19 % or more

TYPICAL MALFUNCTION THRESHOLDS


Solenoid status (SLT) from IC
Fail (Open or short)
(Output signal duty ratio equal to 100 %)

COMPONENT OPERATING RANGE


Output signal duty ratio
Less than 100 %

WIRING DIAGRAM


C121790E04


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION WIRE (SLT)
C121788E02
  1. Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    2 (SLT+) - 6 (SLT-)
    5.0 to 5.6 Ω at 20°C (68°F)
    2 (SLT+) - Body ground
    10 kΩ or higher
    6 (SLT-) - Body ground
    10 kΩ or higher



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C095812E40
  1. Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    E5-12 (SLT+) - E5-13 (SLT-)
    5.0 to 5.6 Ω at 20°C (68°F)
    E5-12 (SLT+) - Body ground
    10 kΩ or higher
    E5-13 (SLT-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM 

3.INSPECT SHIFT SOLENOID VALVE (SLT)
G020767E36
  1. Remove the shift solenoid valve (SLT).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    1 - 2
    5.0 to 5.6 Ω at 20°C (68°F)

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (SLT)
OK

REPAIR OR REPLACE TRANSMISSION WIRE