Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P0051    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)

DTC    P0052    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)

for Preparation Click here

HINT:
  1. Although the DTC titles say the oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 .

HINT:
  1. When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned OFF.
  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


A115897E02


DTC No.
DTC Detection Conditions
Trouble Areas
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater
  3. A/F sensor heater relay
  4. ECM
P0032
P0052
Air-Fuel Ratio (A/F) sensor heater current more than 10 A (1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater
  3. A/F sensor heater relay
  4. ECM

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.
The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor will be inaccurate, as a result, the ECM will be unable to regulate air-fuel ratio properly.
When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and sets a DTC.
Example:
The ECM sets DTC P0032 or P0052 when the current in the A/F sensor heater is more than 10 A. Conversely, when the heater current is less than 0.8 A, DTC P0031 or P0051 is set.

MONITOR STRATEGY


Related DTCs
P0031: A/F sensor heater (bank 1) open/short (Low electrical current)
P0032: A/F sensor heater (bank 1) open/short (High electrical current)
P0051: A/F sensor heater (bank 2) open/short (Low electrical current)
P0052: A/F sensor heater (bank 2) open/short (High electrical current)
Required Sensors/Components (Main)
A/F sensor heater (bank 1 and 2)
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
10 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
None

P0031 and P0051: 
Battery voltage
10.5 V or more
A/F sensor heater duty-cycle ratio
50 % or more
Time after engine start
10 seconds or more

P0032 and P0052: 
Time after engine start
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0031 and P0051: 
A/F sensor heater current
Less than 0.8 A

P0032 and P0052: 
A/F sensor heater current
More than 10 A

COMPONENT OPERATING RANGE


A/F sensor heater current
1.8 to 3.4 A at 20°C (68°F)

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A085152E44
  1. Disconnect the A4 or A5 A/F sensor connector.

  1. Measure the resistance between the terminals of the A/F sensor connector.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    HT (1) - +B (2)
    1.8 to 3.4 Ω at 20°C (68°F)
    HT (1) - AF- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


2.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY
B016200E02
  1. Remove the A/F sensor heater relay from the engine room relay block.

  1. Check the A/F sensor heater relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the A/F sensor heater relay.



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY
OK


3.INSPECT ECM (HA1A OR HA2A VOLTAGE)
A115970E01
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E5 ECM connector.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    HA1A (E5-2) - E04 (E5-7)
    9 to 14 V
    HA2A (E5-1) - E05 (E5-6)

    HINT:
    1. The HA1A means the A/F sensor bank 1 sensor 1.
    2. The HA2A means the A/F sensor bank 2 sensor 1.



OK
REPLACE ECM
NG


4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM, A/F SENSOR - A/F SENSOR HEATER RELAY)
A116153E04
  1. Check the harness and the connector between the ECM and the A/F sensor.

    1. Disconnect the A4 or A5 A/F sensor connector.

    2. Disconnect the E5 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      HT (A4-1) - HA1A (E5-2)
      Below 1 Ω
      HT (A5-1) - HA2A (E5-1)

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      HT (A4-1) or HA1A (E5-2) - Body ground
      10 kΩ or higher
      HT (A5-1) or HA2A (E5-1) - Body ground

    4. Reconnect the A/F sensor connector.

    5. Reconnect the ECM connector.



  1. Check the harness and the connector between the A/F sensor and A/F sensor heater relay.

    1. Disconnect the A4 or A5 A/F sensor connector.

    2. Remove the A/F sensor heater relay from the engine room relay block.



    3. G035625E02
    4. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      +B (A4-2) - A/F sensor heater relay (3)
      Below 1 Ω
      +B (A5-2) - A/F sensor heater relay (3)

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      +B (A4-2) or A/F sensor heater relay (3) - Body ground
      10 kΩ or higher
      +B (A5-2) or A/F sensor heater relay (3) - Body ground

    5. Reconnect the A/F sensor connector.

    6. Reinstall the A/F sensor heater relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM