CAN COMMUNICATION SYSTEM > Short in CAN Bus Lines |
| Symptom | Trouble Area |
| Resistance between terminals 6(CANH) and 14(CANL) of the DLC3 is below 54 Ω. |
|

| 1.CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 SUB BUS LINE) |
![]() |
Disconnect the DLC3 sub bus line connector (J10) from the CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 1 MΩ or more |
|
| ||||
| OK | |
| 2.CONNECT CONNECTOR |
Reconnect the DLC3 sub bus line connector (J10) to the CAN J/C.
| NEXT | |
| 3.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU SUB BUS LINE) |
![]() |
Disconnect the skid control ECU sub bus line connector (J6) from the CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | |
| 4.CONNECT CONNECTOR |
Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.
| NEXT | |
| 5.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR SUB BUS LINE) |
![]() |
Disconnect the yaw rate sensor sub bus line connector (J7) from the CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | |
| 6.CONNECT CONNECTOR |
Reconnect the yaw rate sensor sub bus line connector (J7) to the CAN J/C.
| NEXT | |
| 7.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR SUB BUS LINE) |
![]() |
Disconnect the steering angle sensor sub bus line connector (J8) from the CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | |
| 8.CONNECT CONNECTOR |
Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.
| NEXT | |
| 9.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN BUS LINE) |
![]() |
Disconnect the ECM main bus line connector (J10) from the CAN J/C.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 108 to 132 Ω |
|
| ||||
| NG | ||
| ||
| 10.CONNECT CONNECTOR |
Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.
| NEXT | |
| 11.CHECK CAN BUS LINES FOR SHORT CIRCUIT (SKID CONTROL ECU SUB BUS LINE) |
Disconnect the skid control ECU connector (S1).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | ||
| ||
| 12.CONNECT CONNECTOR |
Reconnect the yaw rate sensor sub bus line connector (J7) to the CAN J/C.
| NEXT | |
| 13.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR SUB BUS LINE) |
Disconnect the yaw rate sensor connector (Y1).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | ||
| ||
| 14.CONNECT CONNECTOR |
Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.
| NEXT | |
| 15.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR SUB BUS LINE) |
Disconnect the steering angle sensor connector (S9).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 54 to 69 Ω |
|
| ||||
| NG | ||
| ||
| 16.CONNECT CONNECTOR |
Reconnect the ECM main bus line connector (J10) to the CAN J/C.
| NEXT | |
| 17.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN BUS LINE) |
Disconnect the ECM connector (E7).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| D4-6 (CANH) - D4-14 (CANL) |
| 108 to 132 Ω |
|
| ||||
| NG | ||
| ||