Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

A short to +B is suspected in the CAN bus line when there is continuity between terminals 16 (BAT) and 6 (CANH) or terminals 16 (BAT) and 14 (CANL) of the DLC3.

Symptom
Trouble Area
There is continuity between terminals 16 (BAT) and 6 (CANH) or 16 (BAT) and 14 (CANL) of the DLC3.
  1. Short to +B in CAN bus line
  2. ECM
  3. Skid control ECU
  4. Steering angle sensor
  5. Yaw rate sensor

WIRING DIAGRAM


B125031E08


INSPECTION PROCEDURE

1.CHECK CAN BUS LINES FOR SHORT TO +B (DLC3 SUB BUS LINE)


    G031933E13
  1. Disconnect the DLC3 sub bus line connector (J9) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



NG
REPAIR OR REPLACE DLC3 BRANCH LINE OR CONNECTOR (CAN-H,CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the DLC3 sub bus line connector (J9) to the CAN J/C.


NEXT


3.CHECK CAN BUS LINES FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)


    G031932E78
  1. Disconnect the skid control ECU sub bus line connector (J6) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
Go to step 10
NG


4.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.


NEXT


5.CHECK CAN BUS LINES FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)


    G031933E10
  1. Disconnect the yaw rate sensor sub bus line connector (J7) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
Go to step 12
NG


6.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J7) to CAN J/C.


NEXT


7.CHECK CAN BUS LINES FOR SHORT TO +B (STEERING ANGLE SENSOR SUB BUS LINE)


    G031933E11
  1. Disconnect the steering angle sensor sub bus line connector (J8) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
Go to step 14
NG


8.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.


NEXT


9.CHECK CAN BUS LINES FOR SHORT TO +B (ECM MAIN BUS LINE)
  1. Disconnect the ECM sub bus line connector (E7).



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
REPLACE ECM
NG

REPAIR OR REPLACE ECM MAIN BUS LINE OR CONNECTOR (CAN-H,CAN-L) 

10.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.


NEXT


11.CHECK CAN BUS LINES FOR SHORT TO +B (SKID CONTROL ECU SUB BUS LINE)
  1. Disconnect the skid control ECU connector (S1).



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
REPLACE MASTER CYLINDER SOLENOID
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH LINE OR CONNECTOR (CAN-H,CAN-L) 

12.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J7) to the CAN J/C.


NEXT


13.CHECK CAN BUS LINES FOR SHORT TO +B (YAW RATE SENSOR SUB BUS LINE)
  1. Disconnect the yaw rate sensor connector (Y1).



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE YAW RATE SENSOR SUB BUS LINE CONNECTOR (CAN-H,CAN-L) 

14.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.


NEXT


15.CHECK CAN BUS LINES FOR SHORT TO +B (STEERING SENSOR SUB BUS LINE)
  1. Disconnect the steering angle sensor connector (S9).



    G026206E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-16 (BAT)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    D4-14 (CANL) - D4-16 (BAT)



OK
REPLACE STEERING ANGLE SENSOR
NG

REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH LINE OR CONNECTOR (CAN-H,CAN-L)