Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line

for Preparation Click here


DESCRIPTION

A short to GND is suspected in the CAN bus line when there is continuity between terminals 4 (CG) and 6 (CANH) or terminals 4 (CG) and 14 (CANL) of the DLC3.

Symptoms
Trouble Area
There is continuity between terminals 4 (CG) and 6 (CANH) or terminals 4 (CG) and 14 (CANL) of the DLC3.
  1. Short to GND in CAN bus line
  2. ECM
  3. Skid control ECU
  4. Steering angle sensor
  5. Yaw rate sensor
  6. CAN J/C

WIRING DIAGRAM


B125030E02


INSPECTION PROCEDURE

1.CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 SUB BUS LINE)


    G031933E13
  1. Disconnect the DLC3 sub bus line connector (J9) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    1 MΩ or more
    KD4-14 (CANL) - D4-4 (CG)



NG
REPAIR OR REPLACE DLC3 BRANCH LINE OR CONNECTOR (CAN-H,CAN-L)
OK


2.CONNECT CONNECTOR
  1. Reconnect the DLC3 sub bus line connector (J9) to the CAN J/C.


NEXT


3.CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU SUB BUS LINE)


    G031932E78
  1. Disconnect the skid control ECU sub bus line connector (J6) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
Go to step 10
NG


4.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.


NEXT


5.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR SUB BUS LINE)


    G031933E10
  1. Disconnect the yaw rate sensor sub bus line connector (J7) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



NG
Go to step 12
OK


6.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J7) to the CAN J/C.


NEXT


7.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR SUB BUS LINE)


    G031933E11
  1. Disconnect the steering angle sensor sub bus line connector (J8) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
Go to step 14
NG


8.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.


NEXT


9.CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN BUS LINE)


    G031933E12
  1. Disconnect the ECM main bus line connector (J10) from the CAN J/C.

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    1. Reconnect the connector to its original position.



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
Go to step 16
NG

REPLACE CAN J/C 

10.CONNECT CONNECTOR
  1. Reconnect the skid control ECU sub bus line connector (J6) to the CAN J/C.


NEXT


11.CHECK CAN BUS LINE FOR SHORT TO GND (SKID CONTROL ECU SUB BUS LINE)
  1. Disconnect the skid control ECU connector (S1).



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
REPLACE MASTER CYLINDER SOLENOID
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH LINE OR CONNECTOR (CAN-H,CAN-L) 

12.CONNECT CONNECTOR
  1. Reconnect the yaw rate sensor sub bus line connector (J7) to the CAN J/C.


NEXT


13.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR SUB BUS LINE)
  1. Disconnect the yaw rate sensor connector (Y1).



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6(CANH) - D46-4(CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14(CANL) - D4-4(CG)



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE YAW RATE SENSOR SUB BUS LINE OR CONNECTOR (CAN-H,CAN-L) 

14.CONNECT CONNECTOR
  1. Reconnect the steering angle sensor sub bus line connector (J8) to the CAN J/C.


NEXT


15.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR SUB BUS LINE)
  1. Disconnect the steering angle sensor connector (S9).



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
REPLACE STEERING ANGLE SENSOR
NG

REPAIR OR REPLACE STEERING ANGLE SENSOR BRANCH LINE OR CONNECTOR (CAN-H,CAN-L) 

16.CONNECT CONNECTOR
  1. Reconnect the ECM main bus line connector (J10) to the CAN J/C.


NEXT


17.CHECK CAN BUS LINE FOR SHORT TO GND (ECM MAIN BUS LINE)
  1. Disconnect the ECM connector (E7).



    G026206E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    D4-6 (CANH) - D4-4 (CG)
    1. Ignition switch OFF
    2. Stop light switch OFF
    3 kΩ or more
    D4-14 (CANL) - D4-4 (CG)



OK
REPLACE ECM
NG

REPAIR OR REPLACE ECM MAIN BUS LINE OR CONNECTOR (CAN-H,CAN-L)