Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.
If the ignition switch is turned OFF, the ECM holds the EFI relay ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.

WIRING DIAGRAM


A115956E01


INSPECTION PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
G100798E04
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E8 and E6 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (E8-1) - E1 (E6-1)
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
G035617E01
  1. Disconnect the E6 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    E1 (E6-1) - Body ground
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (IGSW VOLTAGE)
G100798E05
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E8 and E6 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    IGSW (E8-9) - E1 (E6-1)
    9 to 14 V



OK
Go to step 6
NG


4.CHECK FUSE (IGN FUSE)
G035653E03
  1. Remove the IGN fuse from the driver side J/B.

  1. Check the IGN fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


5.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
A056879E23
  1. Disconnect the I7 ignition switch connector.

  1. Check the resistance.

    Standard Resistance:
    Ignition Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2-4
    Below 1 Ω
    ON
    1-2, 1-4, 5-6
    START
    1-3, 1-4, 3-4, 5-6, 5-7, 6-7

  1. Reconnect the ignition switch connector.



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
OK

CHECK AND REPLACE HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM) 

6.INSPECT ECM (MREL VOLTAGE)
G100798E06
  1. Turn the ignition switch ON.

  1. Measure the voltage between the terminals of the E6 and E8 ECM connectors.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    MREL (E8-8) - E1 (E6-1)
    9 to 14 V



NG
REPLACE ECM
OK


7.CHECK FUSE (EFI FUSE)
G035646E03
  1. Remove the EFI fuse from the engine room R/B.

  1. Check the EFI fuse resistance.

    Standard Resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


8.INSPECT EFI RELAY
B016200E02
  1. Remove the EFI relay from the engine room R/B.

  1. Check the EFI relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the EFI relay.



NG
REPLACE EFI RELAY
OK


9.CHECK HARNESS AND CONNECTOR (EFI RELAY- ECM, EFI RELAY - BODY GROUND)
A116165E02
  1. Check the harness and connector between the EFI relay and ECM.

    1. Remove the EFI relay from the engine room R/B.

    2. Disconnect the E8 ECM connector.

    3. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI relay (1) - MREL (E8-8)
      Below 1 Ω

      Standard Resistance (Check for short):
      Tester Connections
      Specified Conditions
      EFI relay (1) or MREL (E8-8) - Body ground
      10 kΩ or higher

    4. Reinstall the EFI relay.

    5. Reconnect the ECM connector.

  1. Check the harness and connector between the EFI relay and body ground.

    1. Remove the EFI relay from the engine room R/B.

    2. Check the resistance.

      Standard Resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI relay (2) - Body ground
      Below 1 Ω

    3. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK AND REPAIR HARNESS AND CONNECTOR (TERMINAL +B OF ECM - BATTERY POSITIVE TERMINAL)