DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2238 P2241 |
|
|
| P2239 P2242 | AF+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) | |
| P2252 P2255 | AF- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic) | |
| P2253 P2256 | AF- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
| Related DTCs | P2238: A/F sensor (Bank 1) open circuit between AF+ and AF- P2238: A/F sensor (Bank 1) short circuit between AF+ and AF- P2238: A/F sensor (Bank 1) short circuit between AF+ and GND P2239: A/F sensor (Bank 1) short circuit between AF+ and +B P2241: A/F sensor (Bank 2) open circuit between AF+ and AF- P2241: A/F sensor (Bank 2) short circuit between AF+ and AF- P2241: A/F sensor (Bank 2) short circuit between AF+ and GND P2242: A/F sensor (Bank 2) short circuit between AF+ and +B P2252: A/F sensor (Bank 1) short circuit between AF- and GND P2253: A/F sensor (Bank 1) short circuit between AF- and +B P2255: A/F sensor (Bank 2) short circuit between AF- and GND P2256: A/F sensor (Bank 2) short circuit between AF- and +B |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: A/F sensor open circuit between AF+ and AF- 5 seconds: Others |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| AF+ terminal voltage | 0.5 to 4.5 V |
| AF- terminal voltage | 0.5 to 4.5 V |
| Difference between AF+ and AF- terminal voltages | 0.1 to 0.8 V |
| ECT | 20°C (68°F) or more |
| Engine condition | Running |
| Fuel-cut | OFF |
| A/F sensor heater | ON |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Time after ignition switch is OFF to ON | 5 seconds or more |
| Battery voltage | 11 V or more |
| Ignition switch | ON |
| Time after ignition switch is OFF to ON | 5 seconds or more |
| A/F sensor admittance | Below 0.022 1/Ω |
| AF+ terminal voltage | 0.5 V or less |
| Difference between AF+ and AF- terminal voltages | 0.1 V or less |
| AF+ terminal voltage | More than 4.5 V |
| AF- terminal voltage | 0.5 V or less |
| AF- terminal voltage | More than 4.5 V |
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() | - |
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage Almost no reaction | ![]() | ||
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A4 or A5 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY |
![]() |
Remove the A/F sensor heater relay from the engine room R/B.
Check the A/F sensor heater relay resistance.
| Tester Connections | Specified Conditions |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the A/F sensor heater relay.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A4 or A5 A/F sensor connector.
Turn the ignition switch ON.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (A4-2) - Body ground | 9 to 14 V |
| +B (A5-2) - Body ground |
Turn the ignition switch OFF.
Disconnect the E5 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT (A4-1) - HA1A (E5-2) | Below 1 Ω |
| AF+ (A4-3) - A1A+ (E5-22) | |
| AF- (A4-4) - A1A- (E5-30) | |
| HT (A5-1) - HA2A (E5-1) | |
| AF+ (A5-3) - A2A+ (E5-23) | |
| AF- (A5-4) - A2A- (E5-31) |
| Tester Connections | Specified Conditions |
| HT (A4-1) or HA1A (E5-2) - Body ground | 10 kΩ or higher |
| AF+ (A4-3) or A1A+ (E5-22) - Body ground | |
| AF- (A4-4) or A1A- (E5-30) - Body ground | |
| HT (A5-1) or HA2A (E5-1) - Body ground | |
| AF+ (A5-3) or A2A+ (E5-23) - Body ground | |
| AF- (A5-4) or A2A- (E5-31) - Body ground |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | ||
| ||