Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


HINT:
This section describes the standard CAN values for all CAN related components.


CAN JUNCTION CONNECTOR


  1. CAN J/C connectors.

    HINT:
    1. The connectors connected to the CAN J/C can be distinguished by the colors of the bus lines and the connecting side of the connector.
    1. J7, J8, J9 and J10 are interchangeable.


    B125053E02

    Wiring color 
    CAN J/C connectors
    ("A" side, w/ earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    ECM (J10)
    B
    W
    DLC3 (J9)
    Y-B
    L-W
    Steering angle sensor (J8)
    Y-B
    L-W
    Yaw rate sensor (J7)
    W
    R
    Wiring color 
    CAN J/C connectors (B side, w/o earth terminal)
    Color (CAN-H Side)
    Color (CAN-L Side)
    Skid control ECU (J6)
    B
    W



  2. G026205E01
  3. The terminals of the CAN J/C connectors.
    Terminal
    Terminal symbol
    1
    CANH
    2
    CANL



  4. G026214E08
  5. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Specified value
    CANH - CANL
    108 to 132 Ω


DLC3


    G026206E56
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Terminal Description
    Condition
    Specified Condition
    D4-6 (CANH) - D4-14 (CANL)
    HIGH-level CAN bus line - LOW-level CAN bus line
    IG switch OFF
    Stop light switch OFF
    54 to 69 Ω
    D4-6 (CANH) - D4-16 (BAT)
    HIGH-level CAN bus line - Battery positive
    IG switch OFF
    Stop light switch OFF
    1 MΩ or higher
    D4-14 (CANL) - D4-16 (BAT)
    LOW-level CAN bus line - Battery positive
    IG switch OFF
    Stop light switch OFF
    1 MΩ or higher
    D4-6 (CANH) - D4-4 (CG)
    HIGH-level CAN bus line - Ground
    IG switch OFF
    Stop light switch OFF
    3 kΩ or higher
    D4-14 (CANL) - D4-4 (CG)
    LOW-level CAN bus line - Ground
    IG switch OFF
    Stop light switch OFF
    3 kΩ or higher


SKID CONTROL ECU


  1. Check the skid control ECU harness side connector (S1).

    1. Disconnect the connector (S1) from the skid control ECU.



    2. E069126E25
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      S1-11 (CANH) - S1-25 (CANL)
      B-W - W-L
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF
      Stop light switch OFF
      54 to 69 Ω
      S1-11 (CANH) - S1-32 (GND2)
      B-W - W-B
      HIGH-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      S1-25 (CANL) - S1-32 (GND2)
      W-B - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      S1-11 (CANH) - S1-31 (+BS)
      B-W - R
      HIGH-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher
      S1-25 (CANL) - S1-31 (+BS)
      W-L - R
      LOW-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher


STEERING ANGLE SENSOR


  1. Check the harness side connector (S9) of the steering angle sensor.

    1. Disconnect the connector (S9) from the steering angle sensor.



    2. G026210E01
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      S9-3 (CANH) - S9-11 (CANL)
      Y-B - L-W
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF
      Stop light switch OFF
      54 to 69 Ω
      S9-3 (CANH) - S9-2 (ESS)
      Y-B - W-B
      HIGH-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      S9-11 (CANL) - S9-21 (ESS)
      L-W - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      S9-3 (CANH) - S9-9 (BAT)
      Y-B - R
      HIGH-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher
      S9-11 (CANL) - S9-9 (BAT)
      L-W - R
      LOW-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher


YAW RATE SENSOR


  1. Check the yaw rate sensor harness side connector (Y1).

    1. Disconnect the connector (Y1) from the yaw rate sensor.



    2. G026641E06
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      Y1-3 (CANH) - Y1-2 (CANL)
      Y - L
      HIGH-level CAN bus line - LOW-level CAN bus line
      IG switch OFF
      Stop light switch OFF
      54 to 69 Ω
      Y1-3 (CANH) - Y1-1 (GND)
      Y - W-B
      HIGH-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      Y1-2 (CANL) - Y1-1 (GND)
      L - W-B
      LOW-level CAN bus line - Ground
      IG switch OFF
      Stop light switch OFF
      3 kΩ or higher
      Y1-3 (CANH) - D4-16 (BAT)
      Y - Y
      HIGH-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher
      Y1-2 (CANL) - D4-16 (BAT)
      L - Y
      LOW-level CAN bus line - Battery positive
      IG switch OFF
      Stop light switch OFF
      1 MΩ or higher


ECM


  1. Measure the resistance according to the value(s) in the table below.


    G100738E01


    Standard resistance:

    Terminals
    Condition
    Specified Condition
    E7-33 (CANH) - E7-34 (CANL)
    IG switch OFF
    Stop light switch OFF
    108 to 132 Ω



  2. G100737E01
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Terminals
    Wiring Color
    Condition
    Specified Condition
    E7-33 (CANH) - E7-34 (CANL)
    B - W
    IG switch OFF
    Stop light switch OFF
    108 to 132 Ω
    E7-33 (CANH) - E4-7 (E01)
    B - W-B
    IG switch OFF
    Stop light switch OFF
    3 kΩ or more
    E7-34 (CANL) - E4-7 (E01)
    W - W-B
    IG switch OFF
    Stop light switch OFF
    3 kΩ or more
    E7-33 (CANH) - E8-3 (BATT)
    B - L
    IG switch OFF
    Stop light switch OFF
    1 MΩ or more
    E7-34 (CANL) - E8-3 (BATT)
    W - L
    IG switch OFF
    Stop light switch OFF
    1 MΩ or more