WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative |

| 1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
|
| ||||
| NG | |
| 2.REPLACE TRANSMITTER BATTERY |
After replacing the transmitter battery with a new or correctly functioning one, check that the doors can be locked and unlocked by using the transmitter LOCK/UNLOCK switch.
|
| ||||
| NG | |
| 3.CHECK WIRELESS DOOR LOCK FUNCTIONS (STANDARD OPERATION) |
Check standard LOCK/UNLOCK switch operation.
|
| ||||
| NG | |
| 4.CONFIRM ROOM LIGHT ON |
Check that the room laight comes on.
|
| ||||
| OK | |
| 5.SWITCH TO SELF-DIAGNOSTIC MODE |
Switch to self-diagnostic mode by operating the ignition key cylinder.
Put the vehicle into its initial condition (Click here), and insert the key into the ignition key cylinder and remove it.
Within 5 seconds of the key being removed (step 1), insert the key into the ignition key cylinder again (ignition key in the LOCK position). Then turn the ignition switch ON and return it to the LOCK position.
Within 30 seconds of the ignition switch being returned to the LOCK position (step 2), perform the following 9 times: turn the ignition switch ON and return it to the LOCK position.
![]() |
Check that the system has switched to self-diagnostic mode by checking the blinking frequency of the room light.
|
| ||||
| OK | |
| 6.CHECK BY SELF-DIAGNOSTIC MODE |
Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked with the outputs of the room light.

| Result | Proceed to |
| Normal waves (room light blinking) for LOCK and UNLOCK switches are output. | A |
| An unmatching recognition code is output and room light stays ON. | B |
| No diagnosis outputs are present and the room light is OFF. | C |
|
| ||||
|
| ||||
| A | |
| 7.REGISTER RECOGNITION CODE |
Check that the system can switch to rewrite mode or add mode and a recognition code can be registered.
|
| ||||
| OK | ||
| ||
| 8.CHECK RESPONSE OF DOOR CONTROL RECEIVER |
Prepare a new or correctly functioning door control transmitter switch for the same vehicle model. Press and hold a switch on the transmitter and check that an unmatching recognition code is output.
|
| ||||
| OK | ||
| ||
| 9.CONFIRM INPUT METHOD OF SELF-DIAGNOSTIC MODE |
| Result | Proceed to |
| The method for changing the system to self-diagnostic mode works. | A |
| The method for changing the system to self-diagnostic mode does not work. | B |
|
| ||||
| A | |
| 10.INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
![]() |
Remove the unlock warning switch.
Measure the resistance.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Not pushed | 10 kΩ or higher |
| 1 - 2 | Pushed | Below 10 Ω |
Reinstall the unlock warning switch.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - DRIVER SIDE J/B AND BODY GROUND) |
![]() |
Disconnect the U1 unlock warning switch connector.
Disconnect the 1K driver side J/B connector.
Check the resistance.
| Tester Connection | Specified Condition |
| U1-1 - 1K-10 (KSW) | Below 1 Ω |
| U1-2 - Body ground | Below 1 Ω |
Reconnect the unlock warning switch connector.
Reconnect the driver side J/B connector.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND) |
![]() |
Disconnect the D7 door control receiver connector.
Check the voltage and resistance.
| Tester Connection | Specified Condition |
| D7-5 (+B) - Body ground | 10 to 14 V |
| D7-1 (GND) - Body ground | Below 1 Ω |
Reconnect the door control receiver connector.
|
| ||||
| OK | |
| 13.CHECK DOOR CONTROL RECEIVER (OUTPUT) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the connector.
| Tester Connection | Condition | Specified Condition |
| D7-2 (RDA) - Body ground | Each transmitter switch OFF (No key in ignition key cylinder and all doors closed) | Below 1 V |
| D7-2 (RDA) - Body ground | Each transmitter switch ON (No key in ignition key cylinder and all doors closed) | Alternates between 6V and 7V |
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - DRIVER SIDE J/B (ECU AND GROUND)) |
![]() |
Disconnect the D7 door control receiver connector.
Disconnect the B5 multiplex network body ECU connector.
Check the resistance.
| Tester Connection | Specified Condition |
| D7-2 (RDA) - B5-7 (RDA) | Below 1 Ω |
| D7-2 (RDA) - Body ground | 10 kΩ or higher |
| B5-7 (RDA) - Body ground | 10 kΩ or higher |
Reconnect the door control receiver connector.
Reconnect the multiplex network body ECU connector.
|
| ||||
| OK | |
| 15.REPLACE DOOR CONTROL RECEIVER WITH NORMAL ONE |
|
| ||||
| OK | ||
| ||