DTC B1610/13 Front Airbag Sensor RH Circuit Malfunction |
DTC B1615/14 Front Airbag Sensor LH Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Areas |
| B1610/13 |
|
|
| B1615/14 |
|
|

| 1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
Check the DTC (Click here).
| Result | Proceed to |
| DTC B1610/13 is output. | A |
| DTC B1615/14 is output. | B |
| DTC B1610/13 and B1615/14 are output. | C |
| Neither DTC B1610/13 nor B1615/14 is output. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the airbag sensor front RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Check that the connectors (on the center airbag sensor assembly side and airbag sensor front RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.
Using a service wire, connect A12-2 (+SR) and A12-1 (-SR) of connector E.
Measure the resistance.
| Tester connection | Condition | Specified Condition |
| A21-29 (+SR) - A21-27 (-SR) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester connection | Condition | Specified Condition |
| A21-29 (+SR) - A21-27 (-SR) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester connection | Condition | Specified Condition |
| A21-29 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A21-27 (-SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester connection | Condition | Specified Condition |
| A21-29 (+SR) - Body ground | Always | 1 MΩ or higher |
| A21-27 (-SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK FRONT AIRBAG SENSOR RH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the airbag sensor front RH with the front airbag sensor LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1610/13 is output. | A |
| DTC B1615/14 is output. | B |
| Neither DTC B1610/13 nor B1615/14 is output. | C |
|
| ||||
|
| ||||
| A | |
| 9.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 10.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2 -1 (-SR) - IA2-2 (+SR) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 11.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2 -1 (-SR) - IA2-2 (+SR) | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 12.CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| IA2 -1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
| IA2-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 13.CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2 -1 (-SR) - Body ground | Always | 1 MΩ or higher |
| IA2-2 (+SR) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 14.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH.
|
| ||||
| OK | |
| 15.CHECK CONNECTOR |
Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged (Click here).
|
| ||||
| OK | |
| 16.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.
Using a service wire, connect A11-2 (+SL) and A11-1 (-SL) of connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21 -30 (+SL) - A21-28 (-SL) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 17.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21 -30 (+SL) - A21-28 (-SL) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 18.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21 -30 (+SL) - Body ground | Ignition switch ON | Below 1V |
| A21-28 (-SL) - Body ground | Ignition switch ON | Below 1V |
|
| ||||
| OK | |
| 19.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21 -30 (+SL) - Body ground | Always | 1 MΩ or Higher |
| A21-28 (-SL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 20.CHECK FRONT AIRBAG SENSOR LH |
![]() |
Connect the connectors to the center airbag sensor assembly.
Interchange the front airbag sensor RH with the front airbag sensor LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1615/14 is output. | A |
| DTC B1610/13 is output. | B |
| Neither DTC B1610/13 nor B1615/14 is output. | C |
|
| ||||
|
| ||||
| A | |
| 21.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly .
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 22.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - IA2-4 (+SL) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| Go to step 44 |
| 23.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - IA2-4 (+SL) | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| Go to step 44 |
| 24.CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| IA2-4 (+SL) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| Go to step 44 |
| 25.CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - Body ground | Always | 1 MΩ or Higher |
| IA2-4 (+SL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| Go to step 44 |
| 26.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly , the front airbag sensor LH and the front airbag sensor LH.
|
| ||||
| OK | |
| 27.CHECK CONNECTOR |
Check that the connectors (on the center airbag sensor assembly side, front airbag sensor LH side and front airbag sensor RH side) are not damaged (Click here).
|
| ||||
| OK | |
| 28.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.
Using a service wire, connect A12-2 (+SR) and A12-1 (-SR) of connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-29 (+SR) - A21-27 (-SR) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 29.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-29 (+SR) - A21-27 (-SR) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 30.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-29 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| A21-27 (-SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 31.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-29 (+SR) - Body ground | Always | 1 MΩ or Higher |
| A21-27 (+SR) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
|
| ||||
| 32.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-1 (-SR) - IA2-2 (+SR) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 33.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-1 (-SR) - IA2-2 (+SR) | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| 34.CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| IA2-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
| IA2-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 35.CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-1 (-SR) - Body ground | Always | 1 MΩ or Higher |
| IA2-2 (+SR) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| 36.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH.
Using a service wire, connect A11-2 (+SL) and A11-1 (-SL) of connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-30 (+SR) - A21-28 (-SR) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 37.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (FOR SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-30 (+SL) - A21-28 (-SL) | Always | 1 MΩ or Higher |
|
| ||||
| OK | |
| 38.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-30 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| A21-28 (-SL) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 39.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-30 (+SL) - Body ground | Always | 1 MΩ or Higher |
| A21-28 (-SL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
|
| ||||
| 40.CHECK ENGINE ROOM MAIN WIRE (FOR OPEN) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - IA2-4 (+SL) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 41.CHECK ENGINE ROOM MAIN WIRE (FOR SHORT) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - IA2-4 (+SL) | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| 42.CHECK ENGINE ROOM MAIN WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - Body ground | Ignition switch ON | Below 1 V |
| IA2-4 (+SL) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 43.CHECK ENGINE ROOM MAIN WIRE (TO GROUND) |
![]() |
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| IA2-3 (-SL) - Body ground | Always | 1 MΩ or Higher |
| IA2-4 (+SL) - Body ground | Always | 1 MΩ or Higher |
|
| ||||
| OK | ||
| ||
| 44.REPAIR OR REPLACE INSTRUMENT PANEL WIRE |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
Connect the connectors to the center airbag sensor assembly , front airbag sensor RH and front airbag sensor LH .
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||