Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0418    Secondary Air Injection System Control "A" Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0418
  1. After cold engine starts, all of following conditions met (1 trip detection logic):
    1. Air Injection (AIR) system not operating (air pump OFF, Air Switching Valve [ASV] OFF)
    2. Diagnostic signal from Air Injection Control Driver (AID) 20 %
    3. Battery voltage 8 V or more
  1. Open in air pump drive circuit
  2. Short between air pump drive and +B circuits
  3. Air pump
  4. AID
  5. ECM
P0418
  1. After cold engine starts, all of following conditions met (1 trip detection logic):
    1. Air Injection (AIR) system operating (air pump ON, Air Switching Valve [ASV] ON)
    2. Diagnostic signal from Air Injection Control Driver (AID) 20 %
    3. Battery voltage 8 V or more
  1. Short between air pump drive circuit and body ground
  2. Air pump
  3. AID
  4. ECM

MONITOR DESCRIPTION

The Air Injection Control Driver (AID) detects open and short circuits according to the voltages of the air pump terminal (VB) and the Air Switching Valve (ASV) terminal (VV), and transmits diagnostic information as a signal to the ECM.
For a short time after cold engine starts, the ECM transmits command signals to the AID to drive the air pump and ASV.
The AID transmits an air pump malfunction signal to the ECM if either of the following conditions is met:
  1. The voltage at the AID terminal relating to the air pump is low despite the AID receiving command signals from the ECM to drive the air pump.
  2. The voltage at the AID terminal relating to the air pump is high despite the AID receiving no command signals from the ECM to drive the air pump.
The ECM sets the DTC based on diagnostic signals from the AID.

MONITOR STRATEGY


Related DTCs
P0418: Secondary air injection system air pump circuit range check
Required Sensors/Components (Main)
Air injection control driver
Required Sensors/Components (Related)
Air pump
Frequency of Operation
Once per drive cycle
Duration
3 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1: 
Monitor runs whenever following DTCs not present
-
Secondary air injection system
Operating
Battery voltage
8 V or more
Ignition switch
ON
Time after ignition switch OFF to ON
0.5 seconds or more
Starter
OFF
Time after starter turned from ON to OFF
0.5 seconds or more

Case 2: 
Monitor runs whenever following DTCs not present
-
Secondary air injection system
Not operating
Battery voltage
8 V or more
Ignition switch
ON
Time after ignition switch OFF to ON
0.5 seconds or more
Starter
OFF
Time after starter turned from ON to OFF
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Diagnostic signal duty ratio from air injection control driver
11 % or more, and 29 % or less

COMPONENT OPERATING RANGE


Diagnostic signal duty ratio from air injection control driver
70 % or more, and 90 % or less when secondary air injection system operating.
0 % when secondary air injection system not operating.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
Diagnostic information output by the AID can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the AID. Reading the waveform while performing the AIR system intrusive operation provided in the SYSTEM CHECK function, allows the possible trouble areas to be narrowed down.

  1. (a) Start the engine and warm it up.
  2. (b) Turn the ignition switch to OFF.
  3. (c) Connect an intelligent tester to the DLC3.

  4. A065741E10
    (d) Connect oscilloscope probes to the AIDI and E1 terminals of the ECM.
  5. (e) Turn the ignition switch to ON and turn the tester ON.
  6. (f) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL OPERATION / AP: ON, ASV: OPEN and AP: OFF, ASV CLOSE.

    HINT:
    When MANUAL OPERATION is selected, the tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.

  7. (g) Start the engine.

  8. A124516E01
    (h) Perform the AIR system intrusive operation while the engine is idling.

  9. G037721E02
    (i) Monitor the AID voltage output (duty ratio signal).

    Oscilloscope range:
    Items
    Contents
    Terminals
    CH1: AIDI - E1
    Equipment Settings
    5 V/Division, 20 to 50 ms/Division
    Conditions
    Idling


  10. A124517E01
    (j) Turn the ignition switch to OFF.

    NOTICE:
    1. This AIR INJECTION CHECK only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the intelligent tester is prohibited, the tester display indicates the prohibition (WAIT or ERROR).
      If an ERROR as shown in the illustration is displayed on the tester during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the AIR INJ CHECK repetitively may cause damage to the AIR system. If necessary, leave an interval of several minutes between SYSTEM CHECK operations to prevent the system from overheating.
    3. When performing the AIR INJ CHECK operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch to OFF when the AIR INJ CHECK operation finishes.


AID Diagnostic Signal Waveforms
ECM
Commands
DTCs
(ECM Output)
Suspected Trouble Areas
100 % Duty Ratio
See waveform 1
Any Air Injection (AIR) System operation
P1613
  1. Open in diagnostic signal circuit
  2. Air Injection Control Driver (AID)
  3. Open in AID+B circuit (AID power source)
  4. Short between +B and diagnostic signal circuits
0 % Duty Ratio
See waveform 2
AIR System: ON (Air pump ON, ASV ON)
P1613
  1. Open or short in air pump or Air Switching Valve (ASV) command signal circuit (ECM-AID)
  2. Open in AID ground circuit
  3. Short between diagnostic signal circuit and body ground
  4. AID
  5. ECM
AIR System: OFF (Air pump OFF, ASV OFF)
-
Normal
20 % Duty Ratio
See waveform 3
Air Pump: ON
P0418
Short between air pump drive circuit and body ground
  1. Harness and connector (AID-Pump)
  2. Air pump
  3. AID
  4. ECM
Air Pump: OFF
P0418
Open in air pump drive circuit (AID-Pump), or short between air pump drive circuit and +B
  1. Harness and connector (AID-Pump)
  2. Air pump
  3. AID
  4. ECM
40 % Duty Ratio
See waveform 4
ASV: ON
P0412
Short between ASV drive circuit and body ground
  1. Harness and connector (AID-ASV)
  2. ASV
  3. AID
  4. ECM
ASV: OFF
P0412
Open in ASV drive circuit (AID-ASV), or short between ASV drive circuit and +B
  1. Harness and connector (AID-ASV)
  2. AID
  3. ASV
  4. ECM
80 % Duty Ratio
See waveform 5
AIR System: OFF (Air pump OFF, ASV OFF)
P1613
  1. AID
  2. ECM
AIR System: ON (Air pump ON, ASV ON)
-
Normal
Other than above
(other than 0, 20, 40, 80 and 100 % duty)
-
P1613
  1. AID
  2. Open in AID ground circuit

Waveform 1
A112066E01
  1. 100 % Duty Ratio

Waveform 2
A112067E01
  1. 0 % Duty Ratio

Waveform 3
A112068E01
  1. 20 % Duty Ratio

Waveform 4
A112069E01
  1. 40 % Duty Ratio

Waveform 5
A112070E01
  1. 80 % Duty Ratio

HINT:
  1. By using an intelligent tester to perform the AIR INJ CHECK operation in the SYSTEM CHECK, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
  2. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.INSPECT AIR PUMP ASSEMBLY
G037120E05
  1. Disconnect the A9 air pump connector.

  1. Measure the air pump resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    Air pump (A9-1) - Air pump (A9-2)
    0.4 to 10 Ω at 20°C (68°F)

  1. Reconnect the air pump connector.



NG
REPLACE AIR PUMP ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (AIR PUMP - BODY GROUND)
G037119E03
  1. Disconnect the A9 air pump connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    Air Pump (A9-1) - Body ground
    Below 1 Ω

  1. Reconnect the air pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR INJECTION CONTROL DRIVER)
A113664E01
  1. Disconnect the A9 air pump connector.

  1. Disconnect the A6 AID connector.

  1. Check the resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    Air Pump (A9-2) - AID (A6-2)
    Below 1 Ω

  1. Reconnect the air pump connector.

  1. Reconnect the AID connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR INJECTION CONTROL DRIVER