Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

DTC    P0341    Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

The Camshaft Position (CMP) sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed onto the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes through the CMP sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice the voltage is generated 3 times in the CMP sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No.
DTC Detection Conditions
Trouble Areas
P0340
Case 1
  1. No Camshaft Position (CMP) sensor signal to ECM while cranking ( 2 trip detection logic)
Case 2
  1. No CMP sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in CMP sensor circuit
  2. CMP sensor
  3. Camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0341
When crankshaft rotates twice, Camshaft Position (CMP) sensor signal input to ECM 12 times or more (1 trip detection logic)
  1. Open or short in CMP sensor circuit
  2. CMP sensor
  3. Camshaft
  4. Jumped tooth of timing chain
  5. ECM

HINT:
  1. DTC P0340 indicates a malfunction relating to the CMP sensor (+) circuit (the wire harness between the ECM and CMP sensor, and the CMP sensor itself).
  2. DTC P0341 indicates a malfunction relating to the CMP sensor (-) circuit (the wire harness between the ECM and CMP sensor, and the CMP sensor itself).

Reference: Inspection using an oscilloscope
A063955E03

HINT:
  1. The correct waveform is as shown above.
  2. G2 stands for the CMP sensor signal, and NE+ stands for the Crankshaft Position (CKP) sensor signal.
    Items
    Contents
    Terminals
    CH1: G2 - NE-
    CH2: NE+ - NE-
    Equipment Settings
    5 V/Division, 20 ms/Division
    Conditions
    Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the CMP sensor despite the engine revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is set 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0340: Camshaft position sensor range check
P0340: Camshaft position/crankshaft position misalignment
P0341: Camshaft position sensor malfunction
Required Sensors/Components (Main)
Camshaft Position (CMP) sensor
Required Sensors/Components (Related)
Crankshaft Position (CKP) sensor
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
2 driving cycles: CMP sensor range check
Immediate: Camshaft position/crankshaft position misalignment and CMP sensor malfunction
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

Camshaft Position Sensor Range Check P0340: 
Starter
ON
Minimal battery voltage while starter ON
Less than 11 V

Camshaft Position/Crankshaft Position Misalignment P0340: 
Engine speed
600 rpm or more
Starter
OFF

Camshaft Position Sensor Malfunction P0341: 
Starter
After OFF to ON timing

TYPICAL MALFUNCTION THRESHOLDS


Camshaft Position Sensor Range Check P0340: 
CMP sensor signal
No signal

Camshaft Position/Crankshaft Position Misalignment P0340: 
Camshaft position and crankshaft position phase
Misaligned

Camshaft Position Sensor Malfunction P0341: 
Camshaft position and crankshaft position phase
Misaligned
CMP sensor signal per 2 crankshaft revolutions
12 signals or more

COMPONENT OPERATING RANGE


CMP sensor
  1. CMP sensor output voltage fluctuates while camshaft revolving
  2. 3 CMP sensor signals per 2 crankshaft revolutions

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)
G037727E02
  1. Disconnect the C1 Camshaft Position (CMP) sensor connector.

  1. Measure the resistance between terminals 1 and 2.

Standard Resistance:
Tester Connections
Specified Conditions
1 - 2
835 to 1,400 Ω at cold
1 - 2
1,060 to 1,645 Ω at hot

HINT:
Terms cold and hot refer to the temperature of the coils. Cold means approximately -10° to 50°C (14° to 122°F). Hot means approximately 50° to 100°C (122° to 212°F).

  1. Reconnect the CMP sensor connector.



NG
REPLACE CAMSHAFT POSITION SENSOR
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
A113507E01
  1. Disconnect the C1 CMP sensor connector.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    G+ (C1-1) - G2 (E4-26)
    Below 1 Ω
    G- (C1-2) - NE- (E4-34)
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    G+ (C1-1) or G2 (E4-26) - Body ground
    10 kΩ or higher
    G- (C1-2) or NE- (E4-34) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the CMP sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
BR03795E22
  1. Check the CMP sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR
OK


4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
OK

REPLACE ECM