DTC P0450 Evaporative Emission Control System Pressure Sensor / Switch |
DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC | Monitoring Items | Malfunction Detection Conditions | Trouble Areas | Detection Timings | Detection Logic |
| P0450 | Canister pressure sensor voltage abnormal fluctuation | Sensor output rapidly fluctuates beyond upper and lower malfunction thresholds for 0.5 seconds. |
|
| 1 trip |
| P0451 | Canister pressure sensor noise | Sensor output voltage fluctuates frequently in certain time period. |
|
| 2 trip |
| P0451 | Canister pressure sensor voltage fixed | Sensor output voltage does not vary in certain time period. |
|
| 2 trip |
| P0452 | Canister pressure sensor voltage low | Sensor output less than 42.1 kPa for 0.5 seconds. |
|
| 1 trip |
| P0453 | Canister pressure sensor voltage high | Sensor output more than 123.8 kPa for 0.5 seconds. |
|
| 1 trip |
| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Once per driving cycle: P0451 sensor fixed Continuous: P0451 sensor noise, P0450, P0452 and P0453 |
| Duration | - |
| MIL Operation | Immediate: P0450, P0452 and P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever these DTCs not present | None |
| Atmospheric pressure (absolute pressure) | 70 kPa (525 mmHg) or more, less than 110 kPa (825 mmHg) |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4°to 35°C (40° to 95°F) |
| Either of following conditions met | A or B |
| A. Engine | Running |
| B. Soak time (ignition switch OFF time) | 5 hours |
| First time | 7 hours |
| Second time | 9 hours and 30 minutes |
| Monitor runs whenever these DTCs not present | None |
| Atmospheric pressure (absolute pressure) | Less than 70 kPa (525 mmHg), or 110 kPa (825 mmHg) or more |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4°to 35°C (40° to 95°F) |
| Soak time (ignition switch OFF time) | 5 hours |
| First time | 7 hours |
| Second time | 9 hours and 30 minutes |
| Monitor runs whenever these DTCs not present | None |
| Either of following conditions met | (a) or (b) |
| (a) Ignition switch | ON |
| (b) Soak timer | ON |
| P0450: Canister pressure sensor chattering | - |
| Canister pressure sensor output | Less than 42.1 kPa, or more than 123.8 kPa |
| P0451: Canister pressure sensor noise | - |
| Pressure variation indicated by Canister pressure sensor in 10 seconds | More than +- 0.3 kPa (+- 2.25 mmHg) 10 times |
| P0451: Canister pressure sensor fixed | - |
| 0.02 inch leak criterion variation indicated by canister pressure sensor in 10 seconds | Less than 0.65 kPa (4.87 mmHg) |
| P0452: Canister pressure sensor low | - |
| Canister pressure sensor output | Less than 42.1 kPa |
| P0453: Canister pressure sensor high | - |
| Canister pressure sensor output | More than 123.8 kPa |

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the tester ON.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / EVAP / VAPOR PRESS.
Read the EVAP (Evaporative Emission) pressure displayed on the tester.
| Display (DTC Output) | Test Results | Suspected Trouble Areas | Proceed To |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 45 kpa (430 mmHg) |
| A |
| P0453 | More than 120 kPa (900 mmHg) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Turn the ignition switch to OFF.
Disconnect the E8 ECM connector.
Measure the resistance between PPMP terminal of the ECM connector and the body ground.
| Test Results | Suspected Trouble Areas | Proceed To |
| 10 Ω or less |
| A |
| 10 kΩ or more |
| B |
Reconnect the ECM connector.
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the L1 canister connector.
Disconnect the E8 ECM connector.
Check the resistance between PPMP terminal of the ECM connector and the body ground.
| Test Results | Suspected Trouble Areas | Proceed To |
| 10 kΩ or more | Short in canister pressure sensor circuit | A |
| 10 Ω or less | Short in wire harness/connector (ECM - Canister pressure sensor) | B |
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the L1 canister connector.
Turn the ignition switch to ON.
Measure the voltage and resistance of the canister connector.
| Tester Connections | Specified Conditions |
| L1-4 - Body ground | 4.5 to 5.0 V |
| L1-3 - Body ground | 4.5 to 5.0 V |
| L1-2 - Body ground | 100 Ω or less |
| Test Results | Suspected Trouble Areas | Proceed To |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
Reconnect the canister connector.
|
| ||||
|
| ||||
| 5.REPLACE CHARCOAL CANISTER ASSEMBLY |
Replace the canister assembly.

|
| ||||
| 6.REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Wait for at least 60 seconds.
On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO/PENDING CODES.
| NEXT | ||
| ||