Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

DTC    P0503    Vehicle Speed Sensor "A" Intermittent / Erratic / High

for Preparation Click here


DESCRIPTION

Automatic Transaxle Models:
Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A121748E02

Manual Transaxle Models:
Vehicles, which are equipped with manual transaxle, detect the vehicle speed using the No. 1 vehicle speed sensor. The No. 1 vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle or transfer output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A121749E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0500
Automatic transmission:
ECM detects following conditions simultaneously 500 times (1 trip detection logic)
  1. No speed sensor signal while ECM detects No. 2 speed sensor signal
  2. Vehicle speed 6 mph (9 km/h) or more for 4 seconds
  3. Park/Neutral position switch OFF (shift lever other than P and N positions)
Manual transmission:
ECM detects following conditions simultaneously for 8 seconds or more (2 trip detection logic)
  1. No speed sensor signal input
  2. Engine speed 2,000 rpm or more
  3. ECM detects high engine load
  4. Transfer lever in other than N position (4WD)
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM
  4. Skid control ECU
P0503
Momentary interruption and noise are detected when a rapid change of vehicle speed occurs
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM
  4. Skid control ECU

MONITOR DESCRIPTION

Automatic Transaxle Models:
The ECM assumes that the vehicle is being driven, while the vehicle speed sensor signal is being transmitted by the combination meter. If there is no signal from the combination meter, despite the ECM detecting the speed signal from the No. 2 speed sensor, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.
Manual Transaxle Models:
The ECM assumes that the vehicle is being driven, when the indicated engine speed is more than 2,000 rpm and the engine load calculated by the ECM is more than certain level. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.

MONITOR STRATEGY


Related DTCs
P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main)
Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU
Required Sensors/Components (Related)
Park/neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor and Mass Air Flow (MAF) meter
Frequency of Operation
Continuous
Duration
8 seconds: Manual transmission
Conditions met 500 times: Automatic transmission
MIL Operation
2 driving cycles: Manual transmission
1 driving cycle: Automatic transmission
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

With Manual Transmission: 
Engine coolant temperature
70°C (158°F) or more
Engine speed
2,000 rpm or more
Engine load
100 % when engine speed 2,000 rpm (threshold varies with engine speed)
Fuel cut at high engine speed
Not executing

With Automatic Transmission: 
Vehicle speed sensor output
48 pulses or more
Time after following conditions met:
4 seconds or more
Ignition switch
ON
Park/neutral position switch
OFF
Vehicle speed
5.59 mph (9 km/h)
Time after ignition switch turned to ON
0.5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Vehicle speed sensor signal
No pulse input

WIRING DIAGRAM


A121750E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.

    HINT:
    The vehicle speed sensor is operating normally if the speedometer reading is normal.



NG
CHECK SPEEDOMETER CIRCUIT
OK


2.INSPECT ECM (SPD VOLTAGE)
A113675E01
  1. Shift the transmission gear selector lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminals of the ECM connectors as the wheel is turned slowly.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    SPD (E7-8) - E1 (E4-3)
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM