Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

for Preparation Click here

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Conditions
Trouble Areas
P2238
  1. Case 1:
    Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic)
    1. (a) A1A+ voltage 0.5 V or less
    2. (b) (A1A+) - (A1A-) = 0.1 V or less
  1. Case 2:
    A/F sensor admittance: Less than 0.022 1/Ω (2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater
  4. A/F HEATER relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2239
A1A+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater
  4. A/F HEATER relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2252
A1A- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater
  4. A/F HEATER relay
  5. A/F sensor heater and relay circuits
  6. ECM
P2253
A1A- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. A/F sensor heater
  4. A/F HEATER relay
  5. A/F sensor heater and relay circuits
  6. ECM

MONITOR DESCRIPTION

The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or voltage output deviates greatly from the standard range, the ECM determines that there is an open or short malfunction in the A/F sensor circuit.

MONITOR STRATEGY


Related DTCs
P2238: A/F sensor open circuit between A1A+ and A1A-
P2238: A/F sensor short circuit between A1A+ and A1A-
P2238: A/F sensor short circuit between A1A+ and GND
P2239: A/F sensor short circuit between A1A+ and +B
P2252: A/F sensor short circuit between A1A- and GND
P2253: A/F sensor short circuit between A1A- and +B
Required Sensors/Components (Main)
A/F sensor
Required Sensors/Components (Related)
Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

P2238 (open circuit between A1A+ and A1A-): 
Duration while all following conditions met
20 seconds or more
A1A+ terminal voltage
0.5 to 4.5 V
A1A- terminal voltage
0.5 to 4.5 V
Difference between A1A+ and A1A- terminal voltages
0.1 to 0.8 V
ECT
8°C (46°F) or more: closed loop fuel control enable temperature
Engine condition
Running
Time after engine start
20 seconds or more
Fuel-cut
OFF (for 25 seconds or more)
A/F sensor heater duty ratio
0 % or more
Time after A/F sensor heating
20 seconds or more
Battery voltage
10.5 V or more
Ignition switch
ON (for 5 seconds or more)

Others: 
Battery voltage
10.5 V or more
Ignition switch
ON (for 5 seconds or more)

TYPICAL MALFUNCTION THRESHOLDS


P2238 (Open circuit between A1A+ and A1A-): 
A/F sensor admittance
Below 0.022 1/Ω

P2238 (Short circuit between A1A+ and GND): 
A1A+ terminal voltage
0.5 V or less

P2238 (Short circuit between A1A+ and A1A-): 
Difference between A1A+ and A1A- terminal voltages
0.1 V or less

P2239 (Short circuit between A1A+ and +B): 
A1A+ terminal voltage
More than 4.5 V

P2252 (Short circuit between A1A- and GND): 
A1A- terminal voltage
0.5 V or less

P2253 (Short circuit between A1A- and +B): 
A1A- terminal voltage
More than 4.5 V

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Intelligent tester only:
Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE TEST. The A/F CONTROL function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the A/F CONTROL operation using an intelligent tester.

  1. Connect an intelligent tester to the DLC3.
  2. Start the engine and turn the tester ON.
  3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
  4. On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
  5. Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
  6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and OS2 B1S2) displayed on the tester.

    HINT:
    1. The A/F CONTROL operation lowers the fuel injection volume by 12.5 % or increases the injection volume by 25 %.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

      Standard Voltage:

      Tester Display
      (Sensor)
      Injection Volumes
      Status
      Voltages
      AFS B1S1
      (A/F)
      +25 %
      Rich
      Less than 3.0
      AFS B1S1
      (A/F)
      -12.5 %
      Lean
      More than 3.35
      O2S B1S2
      (HO2)
      +25 %
      Rich
      More than 0.5
      O2S B1S2
      (HO2)
      -12.5 %
      Lean
      Less than 0.4

NOTICE:
The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Areas
1
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
-
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
2
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
Output Voltage
Almost
no reaction
A103185
Output Voltage
More than 0.5 V
Less than 0.4 V
A104057
3
Injection Volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
Output Voltage
More than 3.35 V
Less than 3.0 V
A112626
Output Voltage
Almost
no reaction
A103185
4
Injection volume
+25 %
-12.5 %
A103184
Injection Volume
+25 %
-12.5 %
A103184
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system
(Air-fuel ratio extremely lean or rich
Output Voltage
Almost
no reaction
A103185
Output voltage
Almost
no reaction
A103185
  1. Following the A/F CONTROL procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL / USER DATA / AFS B1S1 and O2S B1S2, and press the YES button and then the ENTER button followed by the F4 button.

HINT:
  1. Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A099184E08
  1. Disconnect the A4 Air-Fuel Ratio (A/F) sensor connector.

  1. Measure the resistance between the terminals of the A/F sensor connector.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    HA1A (1) - +B (2)
    1.8 to 3.4 Ω at 20°C (68°F)
    HA1A (1) - A1A- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


2.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F HEATER RELAY)
A054773E02
  1. Remove the A/F HEATER relay from the engine room R/B.

  1. Check the A/F HEATER relay resistance.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage applied to terminals 1 and 2)

  1. Reinstall the A/F HEATER relay.



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY
OK


3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A113406E02

A118002E04

  1. Disconnect the A4 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the +B terminal of the A/F sensor connector and body ground.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    +B (A4-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch to OFF.

  1. Disconnect the E4 ECM connector.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    HA1A (A4-1) - HA1A (E4-1)
    Below 1 Ω
    A1A+ (A4-3) - A1A+ (E4-21)
    Below 1 Ω
    A1A- (A4-4) - A1A- (E4-31)
    Below 1 Ω

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    HA1A (A4-1) or HA1A (E4-1) - Body ground
    10 kΩ or higher
    A1A+ (A4-3) or A1A+ (E4-21) - Body ground
    10 kΩ or higher
    A1A- (A4-4) or A1A- (E4-31) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM