Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2430    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Bank1

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

for Preparation Click here


DESCRIPTION

The Secondary Air injection (AIR) system consists of an air pump, the Air Switching Valve (ASV), a pressure sensor, the Air Injection Control Driver (AID) and the ECM. For a short time after cold engine starts, the AIR system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the ASV.
The AID drives the ASV and the air pump according to command signals transmitted by the ECM. The pressure sensor detects the pressure in the secondary air passage when the AIR system is ON and OFF, and transmits pressure signal to the ECM.
The AID is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the AIR system circuit.

HINT:
As a large current is required to drive the air pump and ASV, an AID has been added to the previous system.


A121746E01


DTC No.
DTC Detection Conditions
Trouble Areas
P2430
While engine running, voltage output of pressure sensor indicates 0.1 V or less, or indicates 4.8V or more (1 trip detection logic
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2431
Pressure sensor indicates less than 45 kPa (338 mmHg), or more than 135 kPa (1,013 mmHg) (2 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2432
While engine running, voltage output of pressure sensor remains below 0.1 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM
P2433
While engine running, voltage output of pressure sensor remains above 4.8 V (1 trip detection logic)
  1. Pressure sensor
  2. Open or short in pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E02
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the pressure sensor or circuit and sets a DTC.

MONITOR STRATEGY


Related DTCs
P2430: Air flow/Pressure sensor circuit range check (Fluctuating)
P2431: Air flow/Pressure sensor circuit rationality
P2432: Air flow/Pressure sensor circuit range check (Low voltage)
P2433: Air flow/Pressure sensor circuit range check (High voltage)
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
P2430, P2432, P2433: 0.5 seconds
P2431: 5 seconds
MIL Operation
P2430, P2432 and P2433: Immediate
P2431: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2430, P2432 and P2433 
Monitor runs whenever following DTCs not present
None
All of following conditions met:
-
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

P2431 Case 1: 
Monitor runs whenever following DTCs not present
None
All following conditions met for:
3 seconds or more
Secondary air injection system
Operating
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

P2431 Case 2: 
Monitor runs whenever following DTCs not present
None
All following conditions met for:
3 seconds or more
Secondary air injection system
Not operating
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P2430: 
Air pressure sensor voltage
Less than 0.1 V, or more than 4.8 V

P2432: 
Air pressure sensor voltage
Less than 0.1 V

P2433: 
Air pressure sensor voltage
More than 4.8 V

P2431: 
Air Pressure
Less than 45 kPa (338 mmHg), or more than 135 kPa (1,013 mmHg)

COMPONENT OPERATING RANGE


Air pressure sensor voltage
Between 0.1 V and 4.8 V

WIRING DIAGRAM


A121762E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
A115626E01
  1. Disconnect the A8 pressure sensor connector.

  1. Disconnect the E4 and E5 ECM connectors.

  1. Check the resistance.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    Pressure sensor (A8-1) - E2 (E4-28)
    Below 1 Ω
    Pressure sensor (A8-2) - AIP (E5-22)
    Below 1 Ω
    Pressure sensor (A8-3) - VC (E4-18)
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    Pressure sensor (A8-2) or AIP (E5-22) - Body ground
    10 kΩ or higher
    Pressure sensor (A8-3) or VC (E4-18) - Body ground
    10 kΩ or higher

  1. Reconnect the pressure sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT ECM (AIP VOLTAGE)
G034995E01
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester ON.

  1. Select the following menu items: DIAGNOSIS / ENHANCED OBD ll / DATA LIST / AIR PMP PRS(A).

  1. Check that the pressure displayed on the tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

    HINT:
    The tester displays the air pump pressure (AIR PMP PRS(A)) as absolute pressure.



NG
REPLACE PRESSURE SENSOR (TURBO PRESSURE SENSOR)
OK

REPLACE ECM