Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

Automatic Transaxle Models:
Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E01

Manual Transaxle Models:
Vehicles, which are equipped with manual transaxle, detect the vehicle speed using the No. 1 vehicle speed sensor. The No. 1 vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle or transfer output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115900E01


DTC No.
DTC Detection Conditions
Trouble Areas
P0500
ECM detects following conditions simultaneously 500 times (1 trip detection logic)
  1. No SP1 (speed sensor) signal while ECM detects SP2 (No. 2 speed sensor) signal
  2. Vehicle speed 6 mph (9 km/h) or more for 4 seconds
  3. Park/Neutral position switch OFF (shift lever other than P and N positions)
  4. Transfer lever in other than N position (4WD)
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM
  4. Skid control ECU

MONITOR DESCRIPTION

Automatic Transaxle Models:
The ECM assumes that the vehicle is being driven, while the vehicle speed sensor signal is being transmitted by the combination meter. If there is no signal from the combination meter, despite the ECM detecting the speed signal from the speed sensor No. 2, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets a DTC.
Manual Transaxle Models:
The ECM assumes that the vehicle is being driven, when the indicated engine speed is more than 2,000 rpm and the engine load calculated by the ECM is more than certain level. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main)
Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU
Required Sensors/Components (Related)
Park/neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor and Mass Air Flow (MAF) meter
Frequency of Operation
Continuous
Duration
8 seconds: Manual transmission
Conditions met 500 times: Automatic transmission
MIL Operation
Immediate: Manual transmission
2 driving cycles: Automatic transmission
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

Manual Transmission: 
Engine coolant temperature
70°C (158°F) or more
Engine speed
2,000 to 6,800 rpm
Fuel cut at high engine speed
Not executing
Engine load
38.5 % at 2,000 rpm
40 % at 3,600 rpm
43.5 % at 5,200 rpm
50 % at 6,800 rpm

Automatic Transmission: 
Time after following conditions met:
4 seconds or more
Ignition switch
ON
Park/neutral position switch
OFF
Vehicle speed
5.59 mph (9 km/h) or more
Time after ignition switch OFF to ON
More than 0.5 seconds

TYPICAL MALFUNCTION THRESHOLDS


Vehicle speed sensor signal
No pulse input

WIRING DIAGRAM


A115942E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check if the operation of the speedometer in the combination meter is normal.

    HINT:
    The vehicle speed sensor is operating normally if the speedometer reading is normal.



NG
CHECK SPEEDOMETER CIRCUIT
OK


2.INSPECT ECM (SPD VOLTAGE)
A116298E01
  1. Shift the transmission gear selector lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch ON.

  1. Check the voltage between the terminals of the E6 and E7 ECM connectors as the wheel is turned slowly.

    Standard:
    Tester Connections
    Specified Conditions
    SPD (E7-8) - E1 (E6-1)
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM