Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

DTC    B2796    No Communication in Immobiliser System

DTC    B2798    Communication Malfunction No. 2

for Preparation Click here


DESCRIPTION

When a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly, DTC B2796 is output. When a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly, DTC B2798 is output.

DTC No.
DTC Detection Conditions
Trouble Areas
B2796
No communication
  1. Key
  2. Wire harness and connector
  3. Transponder key amplifier
  4. Transponder key ECU assembly
B2798
Communication error
Key

WIRING DIAGRAM


B121682E01


INSPECTION PROCEDURE

1.READ VALUE OF INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON with the key that cannot start the engine.

  1. On the intelligent tester enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / IMMOBILISER / IMMOBILISER. Read the values.


Transponder key ECU assembly:

Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
IMMOBILISER
Immobiliser system status / SET or UNSET
UNSET: Ignition switch ON
SET: Without key
-

OK:
"UNSET" (ignition switch ON) appears on the screen.



OK
REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG


2.CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
  1. Check whether the engine starts with the vehicle's other keys.

    OK:
    Engine starts.



OK
RE- REGISTER OR REPLACE KEY THAT CANNOT START ENGINE
NG


3.READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON with the key that will not start the engine.

  1. On the intelligent tester, enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / IMMOBILISER / ANTENNA COIL. Read the values.

    Transponder key ECU assembly:

    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    ANTENNA COIL
    Transponder key coil condition / NORMAL or FAIL
    NORMAL: Transponder key coil is normal
    FAIL: Transponder key coil is malfunctioning
    -

    OK:
    NORMAL (transponder key coil is normal) appears on screen.



OK
REPLACE TRANSPONDER KEY AMPLIFIER
NG


4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TRANSPONDER KEY AMPLIFIER)


    B087953E03
  1. Disconnect the T10 ECU connector.

  1. Disconnect the T9 amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T10-14 (VC5) - T9-1 (VC5)
    Below 1Ω
    T10-15 (CODE) - T9-4 (CODE)
    Below 1Ω
    T10-4 (TXCT) - T9-5 (TXCT)
    Below 1Ω
    T10-5 (AGND) - T9-7 (AGND)
    Below 1Ω
    T10-14 (VC5) or T9-1 (VC5) - Body ground
    10 kΩ or higher
    T10-15 (CODE) or T9-4 (CODE) - Body ground
    10 kΩ or higher
    T10-4 (TXCT) or T9-5 (TXCT) - Body ground
    10 kΩ or higher
    T10-5 (AGND) or T9-7 (AGND) - Body gorund
    10 kΩ or higher

  1. Reconnect the ECU connector.

  1. Reconnect the amplifier connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE TRANSPONDER KEY AMPLIFIER (OPERATION)
  1. After replacing the transponder key amplifier with a normally functioning amplifier, check that the engine starts.

    OK:
    Engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

NORMAL (TRANSPONDER KEY AMPLIFIER DEFECTIVE)